Shindaiwa DGK15FL Скачать руководство пользователя страница 6

Страница: 6 / 54

CAUTION : EXPLOSION



Never use or recharge the battery if the fluid level is below the minimum level.



Do not create sparks or bring flame near the battery as it generates flammable

gas.

CAUTION : FIRE



Do not

carry flammable items (such as fuel, gas and paint) or items that are highly

combustible near the generator as the muffler, exhaust gas and other parts become
extremely hot.



Position this generator 3 ft. (1 m) or more fro

m walls or other hindrances, and on a level

surface.



Do not connect the generator output to indoor wiring.



This generator uses diesel fuel. Always be sure to stop the engine and not bring flames

close when inspecting fuel or refueling. Wait until the engine has cooled before performing
such procedures.



f fuel spills, always be sure to open the spill containment drain valve and drain off the

spilled fuel.



Do not operate the equipment with liquid accumulated in the spill containment.



If fuel or oil

is leaking, repair the leaking location before operation.



Always be sure to wipe up any spilled fuel or oil.



Allow the generator to cool before covering with the protective cover.



Never allow flame to come close to the generator.



Always make sure

that the engine is stopped when working on piping.



After working on the piping, check that there is no fuel leakage.



Absolutely never inspect or perform maintenance to the equipment near fire or other open
flame.

CAUTION : ELECTRIC SHOCK



Do not splash water on equipment or used where exposed to rain.

CAUTION : BURNS



Do not touch the engine and surrounding

components immediately after stopping the

engine as they are still extremely hot.



Do not open the radiator cap immediately after stop

ping the engine. Do so will result in hot

steam gushing out.



Hot steam gushes out from the coolant sub-tank if the generator overheats. Do not touch

the coolant sub-tank.



Always be sure to stop the engine and allow the engine to cool when performing

inspection or maintenance of engine oil. Opening the oil level indicator or oil filler cap
during operation will result in hot oil gushing out.

Содержание DGK15FL























































Результаты поиска

Содержание DGK15FL

Отзывы:

Похожие инструкции для DGK15FL

Бренды по названию

Популярные бренды

Shindaiwa DGK15FL, Руководство владельца и оператора

Результаты поиска

Содержание DGK15FL

Отзывы:

Похожие инструкции для DGK15FL

Бренды по названию

Популярные бренды