Shindaiwa DGK15FL Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 54

background image

14

5-5. Spill Containment Overflow Warning Indicator

If the liquid stored in the spill containment exceeds approximately about 16.1 gal (61 liters)
during operation, the SPILL CONTAINMENT overflow warning indicator illuminates, and the
engine automatically stops. In that case, open the CHECK DOOR and check inside the SPILL
CONTAINMENT whether fuel and oil leak. If so, flush the liquid stored in the spill containment
after repairing the leaking spot.
(Refer to section “

10. Inspection/Maintenance (10) Flushing Liquid in Spill Containment

”.)

< Note >



Although the fluids that can leak internally consist of oil, fuel
and coolant, the spill containment does not have a function
that can separate rainwater that has leaked into the
equipment from these internally leaked fluids. Properly
dispose of liquid drained from the spill containment in a
manner according to the applicable laws and regulations.

5-6. Meters and Gauges

Engine Meters and Gauges

(1) Hour Meter

Displays the operating time. Use this as a reference for
managing periodic inspection interval. Be careful as the hour
meter operates when the ACCESSORY switch is at ON
position regardless of engine is running or not, and / or when
the engine shuts off abnormally when STARTER SWITCH is
set at START position or AUTO position

(Except when Over

Crank Indicator illuminate or flashing).

WARNING : INJURY



Do not open the check door when the starter switch is in the AUTO or START
position. It will cause injury by rotating parts such as cooling fans and fan belt.



Always turn the starter switch to the STOP position and stop the engine, then close

and lock OPERATION PANEL DOOR before checking or maintaining the engine or
any equipment.

CAUTION : BURNS



Do not touch the engine and surrounding components immediately after stopping the
engine as they are still extremely hot.

CAUTION : FIRE



If fuel or oil is leaking, repair the leaking location before operation.

Spill Containment Overflow

Warning Indicator

Hour Meter

«
...
15
16
17
18
19
...
»

Содержание DGK15FL























































Отзывы:

Нет отзывов

Похожие инструкции для DGK15FL

Бренд: Parkside Страницы: 56

Thor 1 TP9000EX

Бренд: TP Radio Страницы: 20

PEAQ PPA55BT-BL

Бренд: Imtron Страницы: 120

Бренд: Durabrand Страницы: 9

Бренд: Ericsson Страницы: 24

Бренд: Saluki Страницы: 243

Бренд: Huawei Страницы: 68

Бренд: Huawei Страницы: 307

DVDLS80 - PORTABLE DVD PLAYER

Бренд: Panasonic Страницы: 32

Бренд: Schulz Страницы: 64

Бренд: Go-Video Страницы: 38

Бренд: All-Power Страницы: 29

Бренд: All-Power Страницы: 43

Бренд: All-Power Страницы: 34

Бренд: Aqua Страницы: 22

Бренд: Roadstar Страницы: 28

Бренд: Roadstar Страницы: 32

Бренд: Roadstar Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды