Shindaiwa DGK15FL Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 54

background image

27

8-4. Checking the Spill Containment

Open the check door and check the inside of the spill containment. Flush out any accumulated
liquid. Refer to section “

10. Inspection/Maintenance (9) Flushing Liquid in Spill

Containment

” for flushing procedures.

< Note >



The types of liquids that can accumulate in the spill containment include oil, fuel, coolant and
battery fluid such that it is not possible to distinguish between rain water and other liquids.
Dispose of flushed liquids according to the related laws and regulations.

8-5. Checking for Fuel, Oil and Coolant Leak

Open the check door and check for fuel, oil and coolant leakage from fuel piping connections
and similar locations.

8-6. Checking the Battery

Check the fluid level, and add distilled water
until it reaches the upper level when the fluid
level is near the lower level.
Check the terminals for looseness and tighten
properly.

Note >



It is necessary to recharge the battery when the
specific gravity of the battery fluid is 1.23 or less.
Request the authorized distributor where the
generator was purchased to recharge the battery.

CAUTION : FIRE



If fuel or oil is leaking, repair the leaking location before operation.

CAUTION : FIRE



If fuel or oil is leaking, repair the leaking location before operation.

California Proposition 65

WARNING

Batteries, battery posts, terminals and related accessories contain lead and lead
compounds, and other chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

CAUTION : EYE/SKIN INJURY



Wear rubber gloves and other protective wear to protect eyes, skin and clothing from
the battery fluid which contains diluted sulfuric acid. If the battery fluid contacts eyes
or skin, wash out immediately with a large amount of water. Be sure to receive
medical treatment, especially if the fluid contacts the eyes.

CAUTION : EXPLOSION



Never use or recharge the battery if the fluid level is below the minimum level.



Do not create sparks or bring flame near the battery as it generates flammable gas.

1

2

Upper Level

(+) Post

(-) Post

Lower Level

Hold-Down

Clamp

«
...
28
29
30
31
32
...
»

Содержание DGK15FL























































Отзывы:

Нет отзывов

Похожие инструкции для DGK15FL

Бренд: Teac Страницы: 6

Music Angel 12031

Бренд: QooPro Страницы: 24

Бренд: Powermate Страницы: 72

Magna Plus 280-430 Frame

Бренд: Marathon Electric Страницы: 20

Бренд: Fermont Страницы: 33

Бренд: ALL POWER AMERICA Страницы: 32

Бренд: Zodiac Страницы: 60

Бренд: Jackery Страницы: 22

Бренд: Jefferson Professional Tools & Equipment Страницы: 9

Бренд: LG Страницы: 18

Бренд: LG Страницы: 20

Бренд: LG Страницы: 18

Бренд: LG Страницы: 35

Бренд: LG Страницы: 23

Бренд: LG Страницы: 48

Бренд: LG Страницы: 7

Бренд: LG Страницы: 3

Бренд: LG Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды