Shindaiwa DGK15FL Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 54

background image

38

(5) Draining Water from the Fuel Filter/Element Replacement

Clean

Every 100 hours

Replace

Every 400 hours

Place a container under Fuel Filter to catch fuel
spilling out of the filter.
Close the fuel valve.
Loosen the retainer ring counterclockwise, and
remove the cup and element.
Remove water or foreign material from the cup and
clean the element using compressed air (or
replace the element).
Reassemble the element and cup to their original
location.

< Note >



Check that no foreign material is adhering to the packing then install the cup.



After installation, turn the fuel valve to OPEN and check that there is no fuel leakage. After
checking, turn the fuel valve to CLOSE.



Always be sure to wipe up any spilled fuel.



If water gathers in the cup, drain water from the fuel tank. (Refer to section
“

10. Inspection/Maintenance (6) Draining Water from the Fuel Tank

”)



Element part no.: 16271-43561 (Kubota part no.)

(6) Draining Water from the Fuel Tank

Drain Water Every

200 hours

Set a container to catch spilled water.
Remove the fuel drain plug and packing (with rubber seal).
After the water has been drained, reinsert the fuel drain plug
with new packing (with rubber seal).

< Note >



Replace the packing of the fuel drain plug with new packing each
time the water is drained.



Packing part no.: V106-000110



After reinserting the fuel drain plug, be sure to always check there
is no fuel leakage.

1

2

3

4

5

1

2

3

Fuel Drain Plug

with Rubber Seal

Close

Fuel Filter

Retainer
Ring

Open

Fuel

Valves

Fuel Filter

Element

Cup

«
...
39
40
41
42
43
...
»

Содержание DGK15FL























































Отзывы:

Нет отзывов

Похожие инструкции для DGK15FL

ProForce PC0102300

Бренд: Powermate Страницы: 36

Бренд: G-Power America Страницы: 53

ElectroMate VEC097

Бренд: Vector Страницы: 20

Бренд: P1PE Страницы: 28

Бренд: Whisper Power Страницы: 24

Бренд: Sound Projections Страницы: 8

Lightolier HC Series

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 40

Бренд: Philips Страницы: 43

Бренд: Champion Power Equipment Страницы: 31

Бренд: Champion Power Equipment Страницы: 2

Бренд: Champion Global Power Equipment Страницы: 33

Бренд: Champion Global Power Equipment Страницы: 4

Бренд: Champion Страницы: 31

Бренд: Champion Страницы: 32

Бренд: Fabco Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды