Shindaiwa C2510 Скачать руководство пользователя страница 32

Страница: 32 / 40

Blade and Trimmer Head

Recommended Blades

WARNING

Non-standard parts may not

operate properly with your unit

and may cause damage and lead

to personal injury.

Make sure to use the following

recommended Shindaiwa blades with

this machine.

Part Number: 60903-98310

8-Tooth Blade

Inner Bore: 25.4 mm

Diameter: 255.0 mm

Thickness: 2.0 mm

Part Number: 60903-98320

4-Tooth Blade

Inner Bore: 25.4 mm

Diameter: 255.0 mm

Thickness: 2.0 mm

Figure 36

Figure 35

Figure 37

Recommended

Trimmer Head

Part Number: 67000-65010

Type: Automatic

Cutting Line: Nylon

Line Diameter: 2.0 mm

Blade Sharpening

With a ﬁle or a grinder, ﬁle a blade as

follows.

WARNING!

Sharpen only the cutting teeth

of a blade. DO NOT alter the

contour of the blade in any way.

In order to keep the blade in

balance, all cutting edges must be

sharpened equally.

DO NOT ﬁle the tips of the teeth

too sharp.

IMPORTANT!

The sharpening angle should be

approximately 45°.

Do not ﬁle the tips of the blade

too sharp. Leave 0.2-0.5 mm

unsharpened.

The bottom of each tooth must

remain unsharpened.

Figure 38

0.2 - 0.5mm

45°

Figure 39

Содержание C2510









































Результаты поиска

Содержание C2510

Отзывы:

Похожие инструкции для C2510

Бренды по названию

Популярные бренды

Shindaiwa C2510, Руководство оператора

Результаты поиска

Содержание C2510

Отзывы:

Похожие инструкции для C2510

Бренды по названию

Популярные бренды