Shindaiwa C2510 Скачать руководство пользователя страница 27

Страница: 27 / 40

HOW TO MAINTAIN AND STORE
Periodic Maintenance

WARNING!

Before performing any

service and maintenance or

repair work on the machine,

make sure that the stop switch

is in the STOP position and the

engine and the cutting attachment

are completely stopped. Always

disconnect the spark plug lead.

General Maintenance

IMPORTANT!

Maintenance, replacement or repair

of emission control devices and

systems may be performed by any

repair establishment or individual;

however, warranty repairs must be

performed by a dealer or service

center authorized by Shindaiwa

Kogyo Co., Ltd. The use of parts that

are not equivalent in performance

and durability to authorized parts

may impair the effectiveness of the

emission Control system and may

have a bearing on the outcome of a

warranty claim.

WARNING!



Before performing any

maintenance, repair or

cleaning work on the unit,

make sure the engine

and cutting attachment

are completely stopped.

Disconnect the spark plug wire

before performing service or

maintenance work.



Non-standard parts may not

operate properly with your unit

and may cause damage and

lead to personal injury.

NOTE:

Using non-standard replacement

parts could invalidate your Shindaiwa

warranty.

Mufﬂer

This unit must never be operated with

a faulty or missing mufﬂer. Make sure

the mufﬂer is well secured and in

good condition. A worn or damaged

mufﬂer is a ﬁre hazard and may also

cause hearing loss.

Spark Plug

Keep the spark plug and wire

connections tight and clean.

Fasteners

Make sure nuts, bolts, and screws

(except carburetor adjusting screws)

are tight.

Blades

WARNING!



Never repair a damaged blade

by welding, straightening, or

by modifying its shape. An

altered blade may break during

operation, resulting in serious

personal injury.



DO NOT use 2-tooth

(lawnmower type) cutting

blades. Use only blades

approved by Shindaiwa for use

with your brushcutter.



Operating the machine with

a blade or attachment not

authorized for use for this

unit can result in serious

injury to the operator and/or

bystanders.



Keep blades sharp and check

blade condition frequently. If

cutting performance changes

suddenly.

Содержание C2510









































Результаты поиска

Содержание C2510

Отзывы:

Похожие инструкции для C2510

Бренды по названию

Популярные бренды

Shindaiwa C2510, Руководство оператора

Результаты поиска

Содержание C2510

Отзывы:

Похожие инструкции для C2510

Бренды по названию

Популярные бренды