Shindaiwa C2510 Скачать руководство пользователя страница 12

Страница: 12 / 40

Installation of the Saw Blade

1. Make sure the switch is off and the

engine is stopped.

2. Wear gloves to protect your hands.
3. Turn the unit over so that the

gearshaft extending from the

gearcase faces up.

4. Using the small end of the plug

wrench, loosen the bolt (turn

clockwise) and remove the bolt,

bolt guard and holder.

Bolt

Bolt Guard

Holder

Safety Clip

Blade

Holder A

Gearcase

Gear Shaft

Figure 11

Figure 12

Safety Clip

Blade

5. Slide the safety clip as the

illustration shows.

WARNING!

Never operate this machine

without the safety clip in place.

6. Fit the blade over the safety clip

and onto Holder A. Then, slide

the safety clip back to the original

position.

WARNING!

The blade must ﬁt ﬂat against the

Holder A. The blade’s mounting

hole must be centered over the

raised boss of Holder A.

7. Put the holder and bolt guard back

and tighten the bolt ﬁnger tight

only at this time. Make sure the

holder is ﬂat against the blade. The

recess in the holder must face the

blade and completely cover the

safety clip.

8. Rotate Holder A until the hole in

its skirt aligns with the hole in the

gearcase. Insert the hex wrench

through both holes (to prevent the

shaft from turning).

9. Holding the hex wrench and

the blade with one hand, tighten

the bolt securely (turn counter-

clockwise) using the small end of

the plug wrench.

10. Remove the hex wrench.

Содержание C2510









































Результаты поиска

Содержание C2510

Отзывы:

Похожие инструкции для C2510

Бренды по названию

Популярные бренды

Shindaiwa C2510, Руководство оператора

Результаты поиска

Содержание C2510

Отзывы:

Похожие инструкции для C2510

Бренды по названию

Популярные бренды