Shindaiwa BP35 Скачать руководство пользователя

Страница: 17 / 20

TR
OUBLESHOO

TING

Troubleshooting Guide

Faulty recoil starter.

Fluid in the crankcase

Internal damage.

Loose spark plug.

Excess wear on cylinder, piston, rings.

Fuel incorrect, stale, or contaminated;

mixture incorrect.

Check for clogged fuel ﬁlter and/or vent.

The ignition switch is in “O” (OFF) position.

Shorted ignition system.

Faulty ignition unit.

If the plug is wet, excess fuel may

be in the cylinder.

The plug is fouled or improperly gapped.

The plug is damaged internally or

of the wrong size.

Consult with an authorized servicing dealer.

Tighten and re-test.

Consult with an authorized servicing dealer.

Reﬁll with clean, fresh unleaded gasoline with a

pump octane of 87 or higher, mixed with Shindaiwa

Premium 2-cycle mixing oil at a 50:1 gasoline/oil ratio.

Replace fuel ﬁlter or vent as required. Restart.

Move switch to “I” (ON) position and re-start.

Consult with an authorized servicing dealer.

Crank the engine with the plug removed, replace the

plug, and restart.

Clean and gap the spark plug to 0.024 inch (0.6mm).

Restart.

Replace the plug with a Champion CJ8 or equivalent

type spark plug of the correct heat range. Restart.

YES

What To Check

Possible Cause

Remedy

ENGINE DOES NOT START

YES

Is the engine overheating?

Engine is rough at all

speeds. May also have black

smoke and/or unburned

fuel at the exhaust.

Operator is overworking the machine.

Carburetor mixture is too lean.

Improper fuel ratio.

Fan, fan cover, cylinder ﬁns dirty or damaged.

Carbon deposits on the piston or in the mufﬂer.

Clogged air cleaner.

Loose or damaged spark plug.

Air leakage or clogged fuel line.

Water in the fuel.

Piston seizure.

Faulty carburetor and/or diaphragm.

Overheating condition.

Improper fuel.

Carbon deposits in the combustion chamber.

Shorten trimmer line. Cut at a slower rate.

Consult with an authorized servicing dealer.

Reﬁll with clean, fresh unleaded gasoline with a

pump octane of 87 or higher, mixed with Shindaiwa

Premium 2-cycle mixing oil at a 50:1 gasoline/oil ratio.

Consult with an authorized servicing dealer.

Clean or replace the air ﬁlter.

Tighten or replace the plug with a Champion CJ8 or

equivalent type spark plug of the correct heat range.

Restart.

Repair or replace fuel ﬁlter and/or fuel line.

Reﬁll with fresh fuel/oil mixture. See page 9.

Consult with an authorized servicing dealer.

See above.

Check fuel octane rating; check for presence of

alcohol in the fuel. See page 9.

Refuel as necessary.

Consult with an authorized servicing dealer.

What To Check

Possible Cause

Remedy

LOW POWER OUTPUT

Engine is knocking.

Does the engine crank?

Good compression?

Does the tank contain fresh fuel

of the proper grade?

Is fuel visible and moving in the

return line when priming?

Is there spark at the spark plug

wire terminal?

Check the spark plug.

Содержание BP35





















Результаты поиска

Содержание BP35

Отзывы:

Похожие инструкции для BP35

Бренды по названию

Популярные бренды

Shindaiwa BP35, Руководство владельца/оператора

Результаты поиска

Содержание BP35

Отзывы:

Похожие инструкции для BP35

Бренды по названию

Популярные бренды