Shindaiwa BP35 Скачать руководство пользователя

Страница: 8 / 20

35015

35012

35013

35011

35010

Assembly

Install the Blade (BP35)

NOTE:

The BP35 is shipped with Holder A, the

safety clip, Holder B, shaft bolt, and bolt

guard installed. The shaft bolt is a LEFT-

HAND THREAD AND IS REMOVED IN A

CLOCKWISE ROTATION!

1. With the gearcase output shaft fac-

ing up, rotate the output shaft and

Holder A until the hole in Holder

A aligns with the matching hole in

the gearcase ﬂange, and then lock

the holder to the gearcase by insert-

ing the long end of the hex wrench

through both holes. See Figure 15.

2. Remove the shaft bolt, bolt guard and

Holder B. See Figure 15.

3. Slide the safety clip off center on the

gearcase shaft. See Figure 15A.

NOTE:

When installing certain blades, it may

be necessary to temporarily remove the

safety clip.

4. Slide the blade over the safety clip

and onto the ﬂange on Holder A.

See Figure 15B.

5. Lock the blade on the shaft by

centering the safety clip.

See Figure 15C.

Shaft Bolt

Bolt Guard

Holder B

Holder A

Output

Shaft

Slide the safety clip off-center

Center the safety clip

Slip the blade into place

Safety Clip

Figure 15

Hex

Wrench

ASSEMBL

WARNING!

Never operate the brushcutter

without the safety clip installed and

both holders tightly secured and ﬂat

against the blade surface!

CAUTION!

Install the blade so the printed

surface is visible to the operator

while the brushcutter is in the normal

operating position.

35014

6. Install Holder B on the gearcase shaft.

See Figure 16.

Install Holder B

Cutting Blade

Tighten the assembly

Combination Spark

Plug/Screwdriver

Wrench

Hex Wrench

Bolt Guard

Holder B

Figure 17

Figure 16

The BP35 should now be completely assembled.

IMPORTANT!

The machined recess in Holder B must

completely surround the safety clip, and

both holders must be ﬂat against the

surface of the blade.

7. Lock Holder A to the gearcase by

inserting the long end of the hex

wrench through both holes as done

in step 1 and tighten the shaft bolt

securely with the combination spark

plug wrench. See Figure 17.

8. Remove the hex wrench.

Содержание BP35





















Результаты поиска

Содержание BP35

Отзывы:

Похожие инструкции для BP35

Бренды по названию

Популярные бренды

Shindaiwa BP35, Руководство владельца/оператора

Результаты поиска

Содержание BP35

Отзывы:

Похожие инструкции для BP35

Бренды по названию

Популярные бренды