Shindaiwa BP35, Руководство владельца/оператора

Страница: 9 / 20

9
35008
CAUTION!

Some gasolines contain alcohol
as an oxygenate! Oxygenated
fuels may cause increased oper-
ating temperatures. Under certain
conditions, alcohol-based fuels
may also reduce the lubricating
qualities of some mixing oils. Nev-
er use any fuel containing more
than 10% alcohol by volume!

Generic oils and some outboard
motor oils may not be intended
for use in high-performance air
cooled 2-cycle engines, and
should never be used in your
Shindaiwa engine!
CAUTION!
This engine is designed to oper-
ate on a 50:1 mixture consisting of
unleaded gasoline and a premium
2-cycle mixing oil only. Use of non-
approved mixing oils can lead to
excessive maintenance costs and/or
engine damage.
ASSEMBL
Y
35007
Assembly
Installing a Trimmer Head
A
Safety Clip
(not used)
Shaft Bolt
(not used)
Bolt Guard
(not used)
NOTE:
The BP35 is shipped with Holder A, the
blade retainer (safety clip), Holder B, shaft
bolt, and bolt guard installed. The shaft
bolt is a LEFT-HAND thread. Remove it by
turning CLOCKWISE!
1. Remove the shaft bolt, bolt guard,
Holder B, safety clip and the existing
cutting attachment.
2. With the gearcase output shaft fac-
ing up, rotate the output shaft and
Holder A until the hole in Holder
A aligns with the matching hole in
the gearcase flange, and then lock
the holder to the gearcase by insert-
ing the long end of the hex wrench
through both holes. See Figure 18A.
3. Using the combination spark plug
wrench, remove the shaft bolt, bolt
guard, Holder B and the safety clip.
(The bolt guard, shaft bolt and safety
clip are not used with a trimmer
head). See Figure 18A.
Output Shaft
Hex Wrench
B
Holder B
Holder A
Hand-tighten Trimmer Head
(counter-clockwise to install)
Figure 18
Mixing Fuel
1. Place the unit on a flat, level surface.
2. Clear any dirt or other debris from
around the fuel filler cap.
3. Remove the fuel cap, and fill the tank
with clean, fresh fuel.
4. Reinstall the fuel filler cap and tighten
firmly.
Filling the Fuel Tank
IMPORTANT!
Mix only enough fuel for your immedi-
ate needs! If fuel must be stored longer
than 30 days and Shindaiwa One oil
with fuel stabilizer is not used, it should
first be treated with a fuel stabilizer
such as STA-BIL™.
WARNING!
Minimize the Risk of Fire!

STOP the engine before
refueling.

ALWAYS allow the unit to cool
before refueling!

Wipe all spilled fuel and move
the unit at least 10 feet (3 me-
ters) from the fueling point before
restarting!

NEVER start or operate this unit if
there is a fuel leak.

NEVER start or operate this unit
if the carburetor, fuel lines, fuel
tank and/or fuel tank cap are
damaged.

NEVER smoke or light any fires
near the unit or fuels!

NEVER place any flammable
material near the engine muffler!

NEVER operate the engine with-
out the muffler and spark arrester
in place and properly functioning!

Use only fresh, clean unleaded gaso-
line with a pump octane rating of 87
or higher.

Mix gasoline with 50:1 Shindaiwa
Premium 2-cycle mixing oil or with an
equivalent high quality 2-cycle mixing
oil.
Example of 50:1 mixing quantities:

1 gallon of gasoline to 2.6 oz. mixing
oil.

5 liters of gasoline to 100 ml. mixing
oil.
4. Install Holder B on the gearcase shaft.
The splined hole on Holder A must
engage with the gearcase shaft.
5. Using the hex wrench to secure
Holder A , install and hand-tighten the
trimmer head (counter-clockwise to
install). See Figure 18B.
6. Remove the hex wrench from the
gearcase and holder.