Shindaiwa BP35 Скачать руководство пользователя

Страница: 18 / 20

TR
OUBLESHOO

TING

Troubleshooting Guide

(continued)

ADDITIONAL PROBLEMS

Poor acceleration.

Clogged air ﬁlter.

Clogged fuel ﬁlter.

Lean fuel/air mixture.

Idle speed set too low.

Switch turned off.

Fuel tank empty.

Clogged fuel ﬁlter.

Water in the fuel.

Shorted spark plug or loose terminal.

Ignition failure.

Piston seizure.

Ground (stop) wire is disconnected,

or switch is defective.

Overheating due to incorrect spark plug.

Overheated engine.

Engine idle too high.

Broken clutch spring or worn clutch spring boss.

Loose attachment holder.

Warped or damaged cutting attachment.

Loose gearcase.

Bent main shaft/worn or damaged bushings.

Shaft not installed in powerhead or gearcase.

Broken shaft.

Damaged gearcase.

Clean or replace the air ﬁlter.

Replace the fuel ﬁlter.

Consult with an authorized servicing dealer.

Adjust: 2,750 (±250) RPM (min

-1

Reset the switch and restart.

Refuel. See page 9.

Replace ﬁlter.

Drain; replace with clean fuel. See page 9.

Clean or replace spark plug with a Champion CJ8 or

equivalent type spark plug of the correct heat range.

Restart. Tighten the terminal.

Replace the ignition unit.

Consult with an authorized servicing dealer.

Test and replace as required.

Replace spark plug with a Champion CJ8 or equivalent

type spark plug of the correct heat range.

Idle engine until cool.

Set idle: 2,750 (±250) RPM (min

-1

Replace spring/shoes as required, check idle speed.

Inspect and re-tighten holders securely.

Inspect and replace attachment as required.

Tighten gearcase securely.

Inspect and replace as necessary.

Inspect and reinstall as required.

Consult with an authorized servicing dealer.

Symptom

Possible Cause

Remedy

Engine stops abruptly.

Engine difﬁcult to shut off.

Excessive vibration.

Cutting attachment rotates at

engine idle.

Cutting attachment will

not rotate.

Содержание BP35





















Результаты поиска

Содержание BP35

Отзывы:

Похожие инструкции для BP35

Бренды по названию

Популярные бренды

Shindaiwa BP35, Руководство владельца/оператора

Результаты поиска

Содержание BP35

Отзывы:

Похожие инструкции для BP35

Бренды по названию

Популярные бренды