Sharp TM150, Руководство по обслуживанию

Страница: 17 / 86

TM150 ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE
2 – 11
CONFIDENTIAL DRAFT
7) Initializing only the file system
Follow the instructions below to initialize only the file system.
(User data will be deleted and the handset status will return to the
default.)
* Perform this procedure when the handset does not turn on.
1
Check the File System Initialize check box.
2
Leave the Load File text box blank.
3
Click the [Start Loading Flash] button.
For further operations, refer to [4-4-3. 4) Rewriting a MOT file] or
[4-4-3. 5) Checking the value of SUM].
4-4-4. Error message list
Below is the list of error messages for the upgrading tool (on the PC
side) and Loading loader (on the handset side).
1) Error messages for the upgrading tool (on the PC side)
2) Error messages for Loading loader (on the handset side)
* When No.1 occurs, handset screen shows error messages for No.2
to No.8 as well as the address (No.10) and status (No.11) of the error
source at the same time.
4-5. RF CALIBRATION & CHECK
4-5-1. Preparation
• Connect PC and GSM tester with a GPIB cable.
• Connect PC and handset with a Data cable.
(Use a test battery or one close.)
• Connect a RF cable of GSM tester to handset.
No. Message Descriptions/Instructions
1 Select a file for Downloading
or check the box of Initializing. Load File is not set. Select
a MOT file.
2 Unable to open file. Failed to open the MOT file.
Start over the rewrite operation.
3 You need to set the Wait Time! WaitTime (S) is not set.
Set WaitTime (S) value.
4 The file you selected is
unsuitable for Upgrading. The selected file cannot be rewrit-
ten for upgrading.
Select an appropriate MOT file.
5 Cannot Setup COM port. The selected COM port does not
exist or is used for other operations.
Select a COM port connected to
the PC cable.
6 RAM Loader not responding
to Commands. No response from Loading loader.
Start over the rewrite operation.
7 RAM Loader responding
Parameter Error. Information sent from the PC is illegal.
Reinstall the upgrading tool. Start
over the rewrite operation.
8 RAM Loader responding
Flash Error (XXXX). Failed to initialize FLASH ROM in
(XXXX).
Start over the rewrite operation.
9 Correspondence Error. Undefined response from Loading
loader.
Start over the rewrite operation.
1 2 3
TM150
TM150
No. Message Descriptions/Instructions
1 FLASH_ERROR An error in Flash Rom.
Start over the rewrite operation.
2 ERROR_PARAM The upgrading tool is damaged.
Uninstall and reinstall the upgrading tool,
and start over the rewrite operation.
3 ERROR_WPROTECT Flash Rom is protected.
Battery may be too low.
Use a sufficiently charged battery and
start over the rewrite operation.
4 ERROR_READ Failed to read Flash Rom data and the
operation was aborted.
Start over the rewrite operation.
5 ERROR_WRITE Failed to write to Flash Rom and the
operation was aborted.
Start over the rewrite operation.
6 ERROR_ERASE Failed to erase Flash Rom data and the
operation was aborted.
Start over the rewrite operation.
7 ERROR_VERIFY The rewrite operation was aborted since
there was a mismatch between data writ-
ten to Flash Rom and that written to
handset.
Start over the rewrite operation.
8 ERROR_RWE_TMOUT Communication was terminated since
there was no response from Flash Rom
for a certain period of time.
Start over the rewrite operation.
9 CORRESPONDENCE
_ERROR Communication was terminated since
serial data communication failed.
Start over the rewrite operation.
10 ADR = XXXXXXXX Indicates the address of Flash
(the error source).
11 STR = XX Indicates the status of Flash
(the error source).
PC
Data cable
Test battery
Stabilized
power supply
RF cable
Handset
GSM tester
GPIB cable