Sharp R-22GT-F Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 48

background image

R-22GT-F
R-22GV-F

19

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

6) Reconnect all leads removed from components during testing.
7) Re-install the outer case (cabinet).
8) Reconnect the power supply cord after the outer case is installed.
9) Run the oven and check all functions.

2. Follow the troubleshooting guide given below, if indicator does not light up after above check and

repairs are finished.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge two high voltage capacitors.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using

insulation tape.

6) After that procedure, re-connect the power supply cord.
7) Follow the troubleshooting guide given below for repair.

STEPS

OCCURRENCE

CAUSE OR CORRECTION

1

The rated AC voltage is not present to power

Check supply voltage and oven power cord.

terminal of CPU connector CN-A.

2

The rated AC voltage is present at primary

Low voltage transformer or secondary circuit defective.

side of low voltage transformer.

Check and repair.

8) Disconnect the power supply cord, and then remove outer case.
9) Open the door and block it open.

10) Discharge two high voltage capacitors.
11) Reconnect all leads removed from components during testing.
12) Re-install the outer case (cabinet).
13) Reconnect the power supply cord after the outer case is installed.
14) Run the oven and check all functions.

«
...
19
20
21
22
23
...
»

Содержание R-22GT-F

















































Отзывы:

Нет отзывов

Похожие инструкции для R-22GT-F

Бренд: GE Страницы: 44

Бренд: GEAppliances Страницы: 16

Бренд: Daewoo Страницы: 17

Бренд: Daewoo Страницы: 38

Бренд: Dacor Страницы: 5

Бренд: Dacor Страницы: 12

Renaissance RO130

Бренд: Dacor Страницы: 2

Бренд: Jenn-Air Страницы: 56

Бренд: Jenn-Air Страницы: 56

Бренд: Samsung Страницы: 52

Бренд: Panasonic Страницы: 110

Бренд: NEFF Страницы: 48

Бренд: Panasonic Страницы: 33

Profile JE2160BF

Бренд: GE Страницы: 2

Бренд: DAEWOO ELECTRONICS Страницы: 21

Бренд: Magic Chef Страницы: 4

Competence B4100-1-WSA

Бренд: AEG Electrolux Страницы: 13

Built-in Microwave Oven

Бренд: Smeg Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды