Sharp R-22GT-F Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 48

background image

R-22GT-F
R-22GV-F

36

DOOR COMPONENTS REMOVAL

DOOR HANDLE REMOVAL

1. Remove the door assembly from oven cavity, referring to

"DOOR REMOVAL".

2. Place door assembly on a soft cloth with latches facing

up.

3. Remove choke cover from door panel, referring to

"CHOKE COVER REMOVAL".

4. Remove two (2) screws holding the door handle to door.
5. Remove the door handle from door panel.
6. Now, door handle is free.

UPPER AND LOWER LATCH HEADS REMOVAL

7. Remove the door release lever from the door assembly.
8. Remove the three (3) screws holding the joint plate to the

door panel.

9. Release the latch spring from the tab of the joint lever and

joint plate.

10.Release the latch heads from joint lever and joint plate.
11.Now, the latch heads are free.

DOOR CASE REMOVAL

1. Remove the door assembly from oven cavity, referring to

"DOOR REMOVAL".

2. Remove choke cover from door panel, referring to

"CHOKE COVER REMOVAL".

3. Remove door handle from door panel, referring to "DOOR

HANDLE REMOVAL".

4. Bend up four (4) nails of door case.
5. Remove door case from door panel.
6. Now, the door case is free.

DOOR GLASS REMOVAL

7. Remove the four (4) screws holding two (2) outside

window fixing plates to door panel.

8. Now, the door glass is free.

«
...
36
37
38
39
40
...
»

Содержание R-22GT-F

















































Отзывы:

Нет отзывов

Похожие инструкции для R-22GT-F

Бренд: Wanderer Страницы: 6

Бренд: RTC Страницы: 83

Бренд: Koenic Страницы: 110

Бренд: Smeg Страницы: 43

Бренд: NEFF Страницы: 32

mobitherm MO-5-12

Бренд: Waeco Страницы: 8

Бренд: NEFF Страницы: 116

Бренд: NEFF Страницы: 64

Бренд: La Germania Страницы: 89

Бренд: Maytag Страницы: 6

Бренд: Smeg Страницы: 18

Бренд: DAEWOO ELECTRONICS Страницы: 22

Бренд: NEFF Страницы: 56

Бренд: Samsung Страницы: 56

Бренд: Hendi Страницы: 108

Бренд: Smeg Страницы: 44

Бренд: Haier Страницы: 16

Бренд: Haier Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды