Sharp R-22GT-F Скачать руководство пользователя страница 34

Страница: 34 / 48

R-22GT-F
R-22GV-F

Hold the magnetron thermistor to the thermistor angle by
bending the tab of the thermistor angle.

5. Insert the thermistor angle between the 2nd. fin and 3rd. fin

from the upper fin of the upper magnetron and push it until
the thermistor angle stops.

NOTE: The magnetron thermistor should be between the

upper fin and the 2nd. fin.

4. Re-install the upper magnetron to the upper waveguide

flange with four (4) screws.

5. Re-install the thermistor angle to the upper waveguide

flange with one (1) screw.

6. Re-install the magnetron exhaust duct to the upper and

lower waveguide flanges with two (2) screws.

7. Route the thermistor harness under the magnetron

temperature fuse.

8. Connect the thermistor harness to the stop switch harness.
9. Connect the wire leads to the upper magnetron, referring to

the pictorial diagram.

10. Re-install the power supply cord, rear cabinet and outer

case cabinet to the oven by reversing the procedures of
"OUTER CASE, REAR CABINET AND POWER SUPPLY
CORD REMOVAL".

CAUTION: WHEN REPLACING MAGNETRON, BE SURE

THE R.F. GASKET IS IN PLACE AND MOUNT-
ING SCREWS ARE TIGHTENED SECURELY.

1. Disconnect the power supply cord and then remove outer

case and rear cabinet , referring to "OUTER CASE, REAR
CABINET AND POWER SUPPLY CORD REMOVAL".

2. Open the oven door and block it open.
3. Discharge two high voltage capacitors.
4. Remove two (2) screws holding ground side terminals of

high voltage rectifier assembly to the capacitor holder and
oven cavity.

5. Disconnect all wire leads from the high voltage capacitor.
6. Disconnect wire leads of high voltage rectifier assembly

from the power transformers (1) and/or (2).
Now, high voltage assembly is free.

7. Remove the three (3) screws holding the blower motor to

the top of oven cavity, the chassis support and air duct.

8. Remove two (2) screws holding the capacitor holder to

oven cavity.

HIGH VOLTAGE CAPACITOR AND HIGH VOLTAGE RECTIFIER ASSEMBLY REMOVAL

Now, the capacitors (1), (2) and the high voltage rectifier
assembly are free.

CAUTION:
1. DISCHARGE THE TWO HIGH VOLTAGE CAPACITOR

BEFORE TOUCHING ANY OVEN COMPONENTS OR
WIRING.

2. DO NOT REPLACE ONLY THE HIGH VOLTAGE

RECTIFIER. IF IT IS DEFECTIVE, REPLACE THE
HIGH VOLTAGE RECTIFIER ASSEMBLY.

3. WHEN REPLACING THE HIGH VOLTAGE RECTIFIER

ASSEMBLY AND THE HIGH VOLTAGE CAPACITOR,
THE GROUND SIDE TERMINAL OF THE HIGH
VOLTAGE RECTIFIER MUST BE SECURED FIRMLY
WITH A GROUNDING SCREW.

1. Disconnect the power supply cord and then remove outer

case and rear cabinet, referring to "OUTER CASE, REAR
CABINET AND POWER SUPPLY CORD REMOVAL".

2. Open the oven door and block it open.
3. Discharge two high voltage capacitors.
4. Disconnect the wire leads from the blower motor and noise

filter.

5. Remove the two (2) screws holding the blower motor angle

BLOWER MOTOR REMOVAL

to the oven cavity.

6. Remove the one (1) screw holding the blower motor angle

to the chassis support.

7. Remove the blower motor from the oven cavity.
8. Remove the two (2) screws holding the noise filter angle to

the blower motor.

9. Now, the blower motor is free.

UPPER

. Disconnect the power supply cord and then remove outer

case, referring to "OUTER CASE, REAR CABINET AND
POWER SUPPLY CORD REMOVAL".

2. Open the oven door and block it open.
3. Discharge two high voltage capacitors.
4. Disconnect the wire leads from the stirrer motor (upper).
5. Remove the one (1) screw holding the stirrer motor (upper)

to the oven cavity.

6. Turn and lift up the stirrer motor (upper).
7. Now, the stirrer motor (upper) is free.

STIRRER MOTORS (UPPER AND LOWER) REMOVAL

LOWER

1. Disconnect the power supply coed.
2. Remove the stirrer motor cover by snipping off the material

in four portions.

3. Where the portions have been snipped off bend the portions

flat. No sharp edge must be evident after removal of the
stirrer motor cover.

4. Disconnect the wire leads from the stirrer motor (lower).
5. Remove the one (1) screw holding the stirrer motor (Lower)

to the oven cavity.

6. Now, the stirrer motor (lower) is free.
7. After replacement use one (1) screw (XOTWW40P08000)

to fit the stirrer motor cover.

HOW TO RELEASE THE POSITIVE LOCK

CONNECTOR.

Procedure

1. Disconnect the power supply cord and then remove outer

case and rear cabinet, referring to "OUTER CASE, REAR

Содержание R-22GT-F

















































Результаты поиска

Содержание R-22GT-F

Отзывы:

Похожие инструкции для R-22GT-F

Бренды по названию

Популярные бренды

Sharp R-22GT-F, Руководство по обслуживанию

Результаты поиска

Содержание R-22GT-F

Отзывы:

Похожие инструкции для R-22GT-F

Бренды по названию

Популярные бренды