Sharp R-22GT-F Скачать руководство пользователя страница 33

Страница: 33 / 48

R-22GT-F
R-22GV-F

11.Loosen the tab of the cord bushing, and remove the

power supply cord with the cord bushing from the rear
cabinet.

12.Remove the cord bushing from the power supply cord,
13.Now, the power supply cord and rear cabinet are free.

8. Disconnect the power supply cord from the supply

harness.

9. Remove the one (1) screw holding the grounding wire of

power supply cord to the oven cavity.

10.Remove the rear cabinet with the power supply cord

from the oven cavity.

POWER TRANSFORMERS (1) AND/OR (2) REMOVAL

Removal

1. Disconnect the power supply cord and then remove

outer case and rear cabinet, referring to "OUTER CASE,
REAR CABINET AND POWER SUPPLY CORD
REMOVAL".

2. Open the oven door and block it open.
3. Discharge two high voltage capacitors.
4. Remove the two (2) screws holding magnetron exhaust

duct to upper and lower waveguide.

5. Remove the magnetron exhaust duct from oven cavity.
6. Disconnect wire leads from magnetrons (1) and/or (2).
7. Disconnect magnetron thermistor from the connector of

the stop switch harness.

8. Remove the one (1) screw holding the thermistor angle

to the upper magnetron.

MAGNETRONS (1) AND/OR (2) REMOVAL

9. Remove the four (4) screws holding each magnetron (1)

and/or (2) to upper and/or lower waveguide. When
removing the screws, hold the magnetron to prevent it
from falling.

10.Remove the magnetrons (1) and/or (2) from upper and/

or lower waveguide with care so magnetron antenna is
not hit by any metal object around antenna.

11.Pull out the thermistor angle from the upper magnetron.
12.Remove the thermo-conductor from the magnetrons (1)

and/or (2).

13.Now, the magnetrons (1) and/or (2) are free.

CAUTION: WHEN REPLACING MAGNETRON, BE SURE

THE R.F. GASKET IS IN PLACE AND MOUNT-
ING SCREWS ARE TIGHTENED SECURELY.

Removal

1. Disconnect the power supply cord and then remove

outer case and rear cabinet, referring to "OUTER CASE,
REAR CABINET AND POWER SUPPLY CORD
REMOVAL".

2. Open the oven door and block it open.
3. Discharge two high voltage capacitors.
4. Remove the upper magnetron from the upper waveguide

flange, referring to "MAGNETRON (1) AND /OR (2)
REMOVAL".

5. Now, the upper magnetron with the magnetron thermistor

should be free.

6. Remove the thermistor angle from the upper magnetron

by pulling out.

7. Straighten the tab of the magnetron thermistor angle

holding the magnetron thermistor.

8. Remove the magnetron thermistor from the thermistor

angle.

9. Now, the magnetron thermistor is free.

MAGNETRON THERMISTOR REPLACEMENT

Re-install

1. Apply the silicone grease (Shinetu silicone grease G746

of Shinetu Chemical Co. Ltd.) to the thermo-conductor
and the magnetron thermistor.

2. Insert the thermo-conductor between the 1st. fin and the

2nd. fin.

3. Install the magnetron thermistor to the thermistor angle

as shown in Figure C-1.

1. Disconnect the power supply cord and then remove

outer case and rear cabinet, referring to "OUTER CASE,
REAR CABINET AND POWER SUPPLY CORD
REMOVAL".

2. Open the oven door and block it open.
3. Discharge two high voltage capacitors.
4. Disconnect wire leads of power transformers (1) and/or

(2) from magnetrons (1) and/or (2).

5. Remove the wire leads of power transformers from the

wire holder.

6. Pull out the wire leads of power transformers from the

tube.

7. Disconnect wire leads of power transformers (1) and/or

(2) from high voltage capacitors (1) and/or (2).

8. Disconnect the high voltage wire lead(s) from power

transformers (1) and/or (2).

9. Disconnect the main wire harness from power

transformers (1) and/or (2).

10.Remove two (2) screws holding each power transformer

(1) and/or (2) to base plate.

11.Remove the power transformers (1) and/or (2) from base

plate.

12.Now, power transformers (1) and/or (2) are free.

Upper magnetron

Upper fin

Apply grease here.

Thermo conductor

Tab

Thermistor
angle

Magnetron
thermistor

Figure C-1. Magnetron thermistor installation

Содержание R-22GT-F

















































Результаты поиска

Содержание R-22GT-F

Отзывы:

Похожие инструкции для R-22GT-F

Бренды по названию

Популярные бренды

Sharp R-22GT-F, Руководство по обслуживанию

Результаты поиска

Содержание R-22GT-F

Отзывы:

Похожие инструкции для R-22GT-F

Бренды по названию

Популярные бренды