Sharp Plasmacluster AE-X12LSR Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 60

background image

AYXP9LSR

3 – 12

2. Troubleshooting of outdoor unit electric components

3. Caution in checking printed circuit boards (PWB)

3.1. Non-insulated control circuit

The GND terminals of the low-voltage circuits (control circuits for microcomputer and thermistors and drive circuits for expansion valve and relays) on
the control printed circuit board (PWB) are connected to the compressor drive power supply (320-VDC negative terminal). Therefore, exercise utmost
caution to prevent electric shock.

If a measuring instrument used for the test is grounded, its chassis (ground) has the same electric potential as the 0-V probe. Since non-insulated cir-
cuits have the following voltage potential difference from the ground, connection of the grounding wire results in a short-circuit between the 0-V line
and the ground, thus allowing an excessive current to flow to the tester to cause damage.

If the sheaths of the thermistor lead wires or expansion valve lead wires inside the outdoor unit become damaged due to pinching by the front panel
or other metal parts or contacting a pipe, a high voltage can flow and destroy the circuits. To prevent these problems, carefully conduct assembly
work.

Does LED light?

NO

YES

YES

NO

Does LED flash?

Normal

NO

YES

NO

YES

NO

YES

NO

YES

Is 230 V applied
between 1 and
N on outdoor
unit terminal
board?

Is voltage between
IPM pins (20) and
(24) 320 V or
higher?

5/ Short-circuit in DC fan motor
Short-circuit in IPM
Short-circuit in diode bridge
Blown fuse
Defective electrolytic capacitor
Wire disconnection, PWB pattern damage
Short-circuit in PAM IGBT (Q5)

Defective switching power supply circuit
Malfunction of 3-terminal regulator IC4, IC1
Short-circuit in expansion valve coil
Malfunction of transistor array IC7
Solder contact or other problems

Malfunction of 3-terminal regulator IC4, IC1

Microcomputer oscillator error
Malfunction of microcomputer reset IC
Malfunction of microcomputer

Malfunction of serial signal circuit
Check wiring between indoor and outdoor units.

Is switching power
supply output of
13 VDC, 15 VDC
produced?

Is 5 VDC output
produced?

Check indoor
unit.

«
...
31
32
33
34
35
...
»

Содержание Plasmacluster AE-X12LSR





























































Отзывы:

Нет отзывов

Похожие инструкции для Plasmacluster AE-X12LSR

Бренд: Samsung Страницы: 35

AC TN4PKG Series

Бренд: Samsung Страницы: 20

Бренд: Fellowes Страницы: 32

Бренд: teca Страницы: 9

Бренд: Trotec Страницы: 16

Бренд: Olmo Страницы: 19

Бренд: Hisense Страницы: 51

Бренд: Daikin Страницы: 20

Air Purifier 60

Бренд: Airfree Страницы: 24

Бренд: Ocean Aire Страницы: 14

23-23-0258N-013 s

Бренд: Fedders Страницы: 31

VRV-WII FXYCP10MY1

Бренд: Daikin Страницы: 35

Бренд: GE Страницы: 32

Бренд: OdorStop Страницы: 12

Бренд: Daikin Страницы: 16

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 40

Бренд: Panasonic Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды