Sharp Plasmacluster AE-X12LSR Скачать руководство пользователя страница 51

Страница: 51 / 60

PARTS GUIDE

CONTENTS

Parts marked with "

" are important for maintaining the safety of the set. Be sure to replace these

parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

AYXP9LSR

SPLIT TYPE
AIR CONDITIONER

MODEL

INDOOR UNIT

AH-XP9LSR
AH-XP12LSR

OUTDOOR UNIT

AE-X9LSR
AE-X12LSR

“HOW TO ORDER REPLACEMENT PARTS”

To have your order filled promptly and correctly, please furnish the
following information.

1. MODEL NUMBER

2. REF. No.

3. PART NO.

4. DESCRIPTION

★

MARK: SPARE PARTS-DELIVERY SECTION

In the interests of user-safety (Required by safety regulations in some countries) the set should
be restored to its original condition and only parts identical to those specified should be used.

PartsGuide

[1] INDOOR UNIT PARTS

[2] INDOOR PACKING PARTS

[3] OUTDOOR UNIT PARTS

[4] OUTDOOR OTHER PARTS

[5] OUTDOOR PACKING PARTS

INDEX

Содержание Plasmacluster AE-X12LSR





























































Результаты поиска

Содержание Plasmacluster AE-X12LSR

Отзывы:

Похожие инструкции для Plasmacluster AE-X12LSR

Бренды по названию

Популярные бренды

Sharp Plasmacluster AE-X12LSR, Руководство по обслуживанию

Результаты поиска

Содержание Plasmacluster AE-X12LSR

Отзывы:

Похожие инструкции для Plasmacluster AE-X12LSR

Бренды по названию

Популярные бренды