Sharp FO-DC635U, Руководство по обслуживанию

Страница: 26 / 166

FO-DC635U
2 – 7
• When the REPORT key is input, the memory dump list is produced
from the displayed address (here, it is limited at the 16-byte bound-
ary address (address with end 0) which does not exceed the speci-
fied address and is just in front.). The dump list is output to a maxi-
mum of 99 pages. If any data of one page can be repeatedly devel-
oped and printed, the list is sufficient. But it is not desired that the
content of plural pages are developed in the memory once and are
then printed. If the STOP key is pressed, it will pass to the diagno-
sis after the page which is now being printed is completed printed.
If the address exceeds the maximum address, it will return to the
address 0 and printing will be continued.
2.1.18 (R) Stamp aging mode
This is a mode to execute the continuous drive aging of the Verification
stamp.
1. Set the document and press down the “START” key and the contin-
uous drive of the Verification stamp starts.
2. Send the document at the interval of 10 mm and stamp the Verifica-
tion stamp continuously. The total number of times of Verification
stamp printing after entering this mode is displayed on the display.
• Displayed screen during execution.
3. By pressing down the “STOP” key during the action, or when no
more document is left, the continuous drive of the Verification
stamp stops.
NOTE: • In case that the document is not set, this cannot be exe-
cuted.
• The normal action aging that one Verification stamp is
pressed on one sheet of document is executed in the nor-
mal copying.
2.1.19 (S) Dial test mode
The mode is used to inspect whether dialing is accurate in two kinds of
dial modes. All data which can be dialed in this mode are automatically
called up in both PB mode and DP mode.
[In case that 2 line optional is not mounted.]
1. Turn on CML, and dial the following in the PB mode.
1, 2, 3, 4, 5, 6, 7, 8, 9, , 0, #
2. Dial the following in the DP mode.
1, 5, 9, 0
3. After dialing, turn off CML.
NOTE: This mode uses the ordinary auto dial. (Accordingly, the signal
sending time and minimum pause are all the same as ordinary. The
measurement result in this mode is completely all the same as in the
ordinary dial mode.)
2.1.20 (T) Copy diag mode
This mode is for automatic mode selection of copy to reduce the time
for treatment at the time of production.
1. Set 2 sheets of document. (No problem if there are 2 sheets or
more.)
2. 3 sheet continuous copy:
1st sheet in the FINE AUTO
2nd sheet and after that are copied in the H-TONE DARK.
NOTE: Input of the image quality and the darkness keys is invalid in
this mode.
2.1.21 (U) LCD check mode
This is an item to check that the LCD acts normally.
1. The screen for selecting the contrast adjustment mode and the “H”
display mode appears.
2. Select the mode using the “
←
” or “
→
” keys or otherwise dial keys
“1” or “2”.
[When the contrast adjustment mode is selected]
3. Adjust with the “
←
” or “
→
” keys so that both right and left halves of
the “A” can be recognized.
[When the “H” display mode is selected]
4. Turn on the backlight so that the whole screen shows “H“. (26 let-
ters x 9 lines)
2.1.22 (V) Personal book list
The PASSCODE of the personal book 00 to 10 are output.
2.1.23 (W) Font list print mode [Only when network func-
tion is mounted]
The font list that can be used in the network function is printed.
2.1.24 (X) No function
2.1.25 (Y) No function
2.1.26 (Z) ADMIN PASSWORD
Print the admin password.
2.1.27 (@)Print hold code
Print the pass code of PRINT HOLD.
STAMP AGING
TIMES = 13 PAGES = 1
Print total number
of times
Page number
U:LCD CHECK MODE
1=CONT.ADJ 2=TEST DISP
CONTRAST=-9 TEMP=+25
A
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH