Sharp FO-DC635U, Руководство по обслуживанию

Страница: 25 / 166

FO-DC635U
2 – 6
2.1.12 (L) Flash Memory check
This is a mode to check that the flash memory acts normally. The flash
memories shown in the following table are checked.
• NAND-Flash (optional) is valid only when the optional memory is
mounted.
1. The NOR flash memory test is executed.
2. The concerned alarm buzzer sounds only when the error occurs.
3. The NAND flash memory test is executed.
4. The concerned alarm buzzer sounds only when the error occurs.
5. The result is printed.
NOTE: • During operation of this diagnosis, dual operation is not
possible at all.
• If this is excessively repeated, it will shorten the life of the
flash memory.
2.1.13 (M) All FAX/TEL. entry mode
This is a function to copy the FAX and TEL numbers registered in the
one-touch dialing (RAPID) key [01] to the all one-touch dialing
(RAPID) key and the all abbreviated number (SPEED DIAL) to simplify
the FAX and TEL number registration at the time of aging. (Only the E-
MAIL can be used for the network models.)
1. Copy the FAX/TEL number or the E-MAIL stored in the RAPID key
[01] to all RAPID keys.
2. Copy the FAX/TEL number or the E-MAIL stored in the RAPID key
[01] to all SPEED DIAL numbers.
3. If the chain dial is not set for the RAPID key, or RAPID key [01]
stores the E-MAIL, the RAPID keys [02] – [59] and all SPEED DIAL
numbers are stored in the group number [01].
4. Enter all registered one-touch send (RAPID) keys and speed dial
numbers (SPEED DIAL) on the personal books [01] - [10]. Follow-
ing this, set the password registration and the password setting to
ON, and set the TTI setting to OFF.
The call-receiver names and book names are specified as follows:
(The letters after 16th letter of the call-receiver’s name registered in
the one-touch dialing [01] are cut off.)
NOTE: Before entering this mode, a FAX/TEL number or an E-MAIL
must be stored in the RAPID key [01]. (This program will not
be executed if there is no data stored, or otherwise a program
or a group is registered.)
2.1.14 (N) Dept. passcode
The department passcode list is printed.
2.1.15 (O) Conf. passcode
The confidential passcode list is printed. Differing from printing of one
box alone soon after registration, the confidential passcodes of all
boxes are printed.
2.1.16 (P) Signal send mode 2
The signals concerned with V.34 & V.8 are checked. It can be used to
check the modem. When the START key is pressed, silence signal
(make loop) will be executed. The following signals are sent by press-
ing the START key thereafter.
2.1.17 (Q) Memory set mode
The set and dump list of the memory content is output.
• The address (8 digits (P) generally including the bank information is
input, and the data of 2 digits is continuously input. Inputting is
done in the hexadecimal mode. The ten-key is used for 0 through
9, and the alphabetic keys A (RAPID 01 through 06) are used for A
through F.
• During data inputting, the address can be moved forward and back-
ward one byte by one byte with " " and "#". (The address prior
to the address 0 is looped as the maximum address.)
• The Validity of the address is not checked. Accordingly, writing/
reading operations are possible in the address of the memory not
assigned, the address of ROM and so on. (However, as practical,
writing is not done, and the data content runs short each reading.)
Though writing is possible in the flash memory, a little time is
required. It is also necessary to take care that the life of the flash
memory is excessively shortened if much data is written in the flash
memory. Since it may run away depending the written content, take
minute care for the writing address.
No. Flash memory Number of
buzzer sound
Remarks
1 NQR-Flash
(Standard) <Long sound>
1 time <Short sound>:
0.5 sec.ON / 0.5
sec.OFF
<Long sounds>:
1.0 sec.ON / 0.5
sec.OFF
2 NAND-Flash
(Standard) <Long sounds>
2 times
3 NAND-Flash
(Option) <Long sounds>
3 times
4 — —
5 — —
NOR FLASH CHECK
S -— — — — — — — E
NAND FLASH CHECK
S -— — — — — — — E
Rapid R XX XX : Rapid key send
SPEED DIAL S XXX XXX : Speed dial number
Personal book BOOK XX XX : Book number
[1] No signals (mark loop) [10] 14400BPS (V. 34)
[2] 33600BPS (V. 34) [11] 12000BPS (V. 34)
[3] 31200BPS (V. 34) [12] 9600BPS (V. 34)
[4] 28800BPS (V. 34) [13] 7200BPS (V. 34)
[5] 26400BPS (V. 34) [14] 4800BPS (V. 34)
[6] 24000BPS (V. 34) [15] 2400BPS (V. 34)
[7] 21600BPS (V. 34) [16] 0 - 300BPS (V. 34)
[8] 19200BPS (V. 34) [17] ANSam
[9] 16800BPS (V. 34)
MEMORY SET MODE
AD = 00000000
Cursor
MEMORY SET MODE
AD = A02800F6 DATA = 0B