Sharp 50NP4 Скачать руководство пользователя страница 12

Страница: 12 / 121

During Insertion

Please refer to direction for insertion as shown in Fig. B (L position). Insert connector until “CLICK” sound is heard.

Make sure the connector is pressed right in, so that it has a good contact with the spring.

Confirm the contact by pulling the connector slightly. (Don’t pull hard because it may damage the connector).

Cover the high voltage output by carefully pushing silicon cover onto it. (Don’t turn the connector).

(REMARK)

Make sure the silicon cover is
covering the high voltage output.

CAUTIONS WHEN CONNECTING / DISCONNECTING THE HV CONNECTOR

Perform the following when the
HV connector (anode connector)
is removed or inserted for CPT
replacement, etc.

Deflection P.W.B.

Silicon cover

Wing

L Position

Wing

FBT

Anode
connector

Remove the connector slowly
by pulling it away from the
case.

During Removal

Roll out silicon cover from FBT’s contact area slowly.

While turning the connector about 90 degrees
following the arrow (0 position), push the connector
slightly towards the case. (Fig. A)

Fig. A

Fig. B

Silicon Cover

less than 1mm

PUSH

Содержание 50NP4


























































































































Результаты поиска

Содержание 50NP4

Отзывы:

Похожие инструкции для 50NP4

Бренды по названию

Популярные бренды

Sharp 50NP4, Руководство по обслуживанию

Результаты поиска

Содержание 50NP4

Отзывы:

Похожие инструкции для 50NP4

Бренды по названию

Популярные бренды