Sharp 50NP4 Скачать руководство пользователя страница 36

Страница: 36 / 121

Important: High Voltage adjustment should

NOT be adjusted in field. This is
adjusted at factory using precise
loads and should NOT

readjusted.

1.4 High Voltage Adjustment (should NOT be

readjusted in field).

Adjustment preparation
(1) Connect High Voltage meter to FBT High Voltage

output. Connect GND of High Voltage meter to CPT
GND or FBT GND.

(2) Check that High Voltage adjustment VR (RH44) is

set to mechanical center(located behind FBT on
DEFLECTION PWB).

(3) Receive circle pattern signal.
(4) VIDEO control should be reset.

Adjustment procedure
(1) Adjust High Voltage to following spec. by turning VR

RH44 clockwise slowly. (This should never need
adjustment).

ADJ. SPEC = 30.0kV +/-0. 5kV

(2) After adjustment, fix VR RH44 by Silicone glue

(KE40RTV).

2. FINAL ASSEMBLY ADJUSTMENT

2.1 Cut Off Adjustment

Adjustment preparation
(1) Set R and G drive VR’s on CPT P.W.B. to center.
(2) Adjust screen VR’s on Focus Pack fully

counterclockwise.

(3) Adjust Focus VR’s on Focus Pack fully

clockwise.

(4) Set video conditions to factory preset.
(5) The vertical incident illumination on the screen

should be 20 lux or less (room should be dark).

CONV.

HEATSINK

DEFLECTION PWB.

RH44

High Voltage Adjustment VR.

T702

(FBT)

Adjustment procedure
(1) Press and hold INPUT key on the control panel

and then POWER ON to access I

C adjustment

mode.

(2) Choose “SERVICE” item from I

C adjustment

menu by pressing

key

(3) Screen VR should be turned clockwise gradually

and set so that retrace line begins to appear.

(4) Return to “NORMAL” mode by CURSOR

key

again.

(5) Adjust Focus VR’s so that focus is even all

around screen.

2.2

DCU Phase Data Setting

Adjustment preparation
(1) Cut off adjustment should finished.
(2) Set video conditions to factory preset.

Adjustment procedure

(1) Receive any NTSC signal.
(2) Push “SERVICE ONLY” switch on

DEFLECTION PWB. (Enter DCU ADJ. mode).

(3) Push HELP key on R/C. (Green cross hatch is

displayed).

Then push EXIT key on R/C. (Character pattern
is displayed. This is the PHASE setting mode).

(4) Set PH-H phase data as shown below by using

4 and 6 key on Remote Control (RC).

(5) Set PH-V phase data as shown below by using

2 and 5 key on R/C.

(6) Set CR-H phase data as shown below by using

CURSOR

and

key on R/C.

(7) Set CR-V phase data as shown below by using

CURSOR

and

key on R/C.

(8) Push HELP key on R/C to exit from the PHASE

mode.

(9) Push PIP MOVE key 2 times on R/C to write the

phase data to memory.

(10) When Green dots are displayed, push MUTE

key to return to DCU ADJ. mode.

(11) Push “SERVICE ONLY” switch to return to RF or

VIDEO mode.

(12) Receive any HD signal (Set to video: 1 or 2

mode with HD input to component jacks).

(13) Repeat steps (2) ˜(11) above.

PROGRESSIVE MODE

TH01

HD MODE

PROGRESSIVE MODE

PHASE MODE

PH-H: BB

PH-V: 0C

CR-H: 4C

CR-V: 00

PHASE MODE

PH-H: BB

PH-V: 07

CR-H: 4C

CR-V: 0C

Содержание 50NP4


























































































































Результаты поиска

Содержание 50NP4

Отзывы:

Похожие инструкции для 50NP4

Бренды по названию

Популярные бренды

Sharp 50NP4, Руководство по обслуживанию

Результаты поиска

Содержание 50NP4

Отзывы:

Похожие инструкции для 50NP4

Бренды по названию

Популярные бренды