SGC SG-2000 Скачать руководство пользователя страница 206

Страница: 206 / 242

SG-2000 MANUAL

199

The SGC Building, 13737 S.E. 26th St. Bellevue, WA. 98005 USA

TEL: (206) 746-6310 FAX: (206) 746-6384

23.5

FINAL ASSEMBLY TESTING PROCEDURES

In addition to the checks, tests, adjustments, measurements and calibrations the

individual PCBs go through, each fully assembled radio is also thoroughly tested before

being sent out to the customer. Though the actual tests are long and detailed, a listing of

the tests performed before any SG-2000 is shipped to a customer will indicate our

commitment to providing the best radio possible.

23.5.1

Pre Rack #1 Tests

The following are the tests performed on each SG-2000 before going on Rack #1

for 12 hours of continuous 100 W CW transmitting on 1.9 MHz into our light

bulb antenna load:

Serial number assignment

Bench inspection (visual, ohms, volts, etc.)

PLLs voltage check and adjustment

Receive SSB sensitivity check

Receive AM sensitivity check

AGC check

ALC 150/50 W transmit adjustment

Carrier insertion check and adjustment

150/50 W power check for for 1.6 to 30 MHz

Head functions check

Communication with SGC Base Station

Antenna mismatch protection in transmit

Recovery at power supply failure

135 W RF Out spectrum quality adjustment

RS-232 port check

11.94 oscillator check

Installation on Rack #1 for 12 hour transmit test and Test Log entry

Содержание SG-2000



















































































































































































































































Результаты поиска

Содержание SG-2000

Отзывы:

SGC SG-2000, Руководство пользователя, Страница: 206 / 242

Результаты поиска

Содержание SG-2000

Отзывы: