SGC SG-2000 Скачать руководство пользователя страница 128

Страница: 128 / 242

SG-2000 MANUAL

121

The SGC Building, 13737 S.E. 26th St. Bellevue, WA. 98005 USA

TEL: (206) 746-6310 FAX: (206) 746-6384

The EXSEL-100 enclosure allows use in automobiles, or alternatively, in base

station installations with transceivers other than the SG-2000. For installation

with units other than the SG-2000, please refer to the EXSEL-100 Interconnection

Diagram for required connections to the transceiver.

19.2

TELEREX™ ARQ/FEC/SELFEC System

The

TELEREX-ST

is an optional sophisticated microprocessor-controlled error-

correcting radio communications data terminal. Despite its considerable

capability, it is extremely easy for the unsophisticated operator to use.

It has been designed primarily for text communication in marine and land based

point-to-point radio links and complies fully with CCIR recommendation 476-4.

It incorporates (optional) Channel Free signal reception and generation, accord-

ing to CCIR recommendation 492-3.

If you have purchased the associated IBM-PC driver software (optional) for the

TELEREX-ST

, you will be almost entirely insulated from the COMMAND code

sequences which are dealt with at length in this manual. Only the initial sections,

covering installation and set up, need be read. From that point, the software is

menu driven. Unless you encounter specific problems, you should not need to

refer to this manual further.

With care in installation and proper attention to the shielding and grounding of

leads, the

TELEREX-ST

should provide many years of reliable service.

The

TELEREX-ST

connects between a radio transceiver and a computer or a

dumb ASCII terminal. Data is passed to the

TELEREX-ST

by means of a serial

RS-232 connection. The computer or terminal must be equipped with a suitable

interface. The unit converts text entered from the terminal into encoded audio

tone signals that are transmitted over the radio link. It also decodes audio signals

from the radio into text to be passed to the terminal, automatically handling all

transmit/receive changeover switching.

MIXED MODE

(Voice-Telex)

OPERATION NOTE:

When using the SG-2000 with the Telerex (or any other data

controller), be sure to remove power from the Telerex unit when

the voice mode is being used in order to avoid the possibility of

transmitting both voice and data at the same time.

Содержание SG-2000



















































































































































































































































Результаты поиска

Содержание SG-2000

Отзывы:

SGC SG-2000, Руководство пользователя, Страница: 128 / 242

Результаты поиска

Содержание SG-2000

Отзывы: