manualshive.com logo in svg

SEW-Eurodrive INTERBUS UFI11A, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive INTERBUS UFI11A Скачать руководство пользователя страница 60

11

60

Manual – Fieldbus Interface INTERBUS UFI11A

List of Errors

91

System error

None

Please check the red SYS-FLT LED 
on the UFI11A. If this LED is on, 
then one or more stations on the 
SBus could not be addressed within 
the timeout delay. If the red SYS-
FLT LED is flashing, then the 
UFI11A itself is in error status. In 
this instance, error 91 alone was 
transmitted to the control via the 
fieldbus.

Check the voltage supply and the 
SBus cabling, check the SBus ter-
minating resistors. Check the con-
figuration if the UFI11A was 
configured with the PC. Switch the 
UFI11A off and on again. Check 
the error code using the diagnostic 
interface if the error remains, and 
take the action described in this 
table.

97

Copy data

SBus communi-
cation stopped

An error occurred while the data 
record was being copied. The data 
are not consistent.

Carry out the "delivery condition" 
factory setting, perform a reset and 
then try to copy the data again.

Error 
code

Name

Response

Cause

Action

Содержание INTERBUS UFI11A





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды