SEW-Eurodrive INTERBUS UFI11A Скачать руководство пользователя страница 59

Страница: 59 / 68

Manual – Fieldbus Interface INTERBUS UFI11A

List of Errors

Error
code

Name

Response

Cause

Action

IPOS ILLOP

IPOS program
stop

Error in IPOS program, see IPOS
variable H469 for more information

Correct the IPOS program, load
and reset

Stack overflow

SBus communi-
cation stopped

Inverter electronics disrupted, pos-
sibly due to effect of EMC

Check ground connections and
shields; improve them if neces-
sary. Contact SEW Service for
advice if this reoccurs.

Stack under-
flow

SBus communi-
cation stopped

NMI

SBus communi-
cation stopped

Undefined
opcode

SBus communi-
cation stopped

Protection
error

SBus communi-
cation stopped

Illegal word
operand
access

SBus communi-
cation stopped

Illegal instruc-
tion access

SBus communi-
cation stopped

Illegal exter-
nal bus access

SBus communi-
cation stopped

EEPROM

SBus communi-
cation stopped

Error when accessing EEPROM

Call up default setting, perform
reset and set parameters of
UFI11A again. Contact SEW Ser-
vice for advice if this reoccurs.

Fieldbus time-
out

Connected inver-
ters stopped
(control word = 0)

No master-slave communication
took place within the configured
response monitoring period.

•

Check master communication
routine

•

Extend the fieldbus timeout
delay (response monitoring) in
the master configuration or turn
off monitoring

IPOS index
overflow

IPOS program
stop

Basic programming rules violated
causing stack overflow in system.

Check IPOS user program and
correct if necessary

Watchdog
error

SBus communi-
cation stopped

Error in system software procedure

Check ground connections and
shields; improve them if neces-
sary. Contact SEW Service for
advice if this reoccurs.

Initialization
error

SBus communi-
cation stopped

Error after self-test in reset

Ensure DIP switches F1 and F2
are off. Perform reset. Contact
SEW Service for advice if problem
persists.

Invalid IPOS
control word

IPOS program
stopped

Attempt was made to set an invalid
automatic mode (via external cont-
rol).

Check write values of external
control

Содержание INTERBUS UFI11A





































































Результаты поиска

Содержание INTERBUS UFI11A

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive INTERBUS UFI11A, Руководство пользователя

Результаты поиска

Содержание INTERBUS UFI11A

Отзывы:

Бренды по названию

Популярные бренды