manualshive.com logo in svg

SEW-Eurodrive INTERBUS UFI11A, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive INTERBUS UFI11A Скачать руководство пользователя страница 50

7

50

Manual – Fieldbus Interface INTERBUS UFI11A

Diagnostic LEDs

LED TR "Trans-
mit" (green)

LED TR "Trans-
mit" (yellow or 
red)

LED "SYS-
FAULT" (red)

LED "USER" 
(green)

Status

Meaning

Remedy

The LED TR corresponds in the color green according to the Interbus standard. 

off

No PCP communication

-

green 

PCP communication active or INTERBUS start (parameter access via 
INTERBUS PCP channel)

-

Status

Meaning

Remedy

The LED TR signals system-internal states with the colors yellow and red that usually do not occur during 
INTERBUS operation.

off or 
green

Standard operation (see table for TR = green)

-

flashing 
yellow

Inverter is in initialization phase

-

steady red

Incorrect DIP switch configuration selected, 
no INTERBUS operation possible.

Check the settings of DIP switch S1. Correct 
the settings of the DIP switches and turn the 
unit on again.

flashing 
red

Incorrect DIP switch configuration or defec-
tive INTERBUS option card, no INTERBUS 
operation possible.

Check the setting of DIP switch S1. If the set-
ting is correct, contact SEW Electronics Ser-
vice.

Status

Meaning

OFF

Standard operating status. The UFI11A is exchanging data with the connected inver-
ters. 

FLASHES 1 x 
briefly with long 
pause

Autosetup has been selected using the DIP switch and the UFI11A is currently set-
ting up its configuration. If this status lasts for more than one minute, turn off the 
Autosetup mode and turn it on again. Replace the module if the behavior persists.

FLASHES regularly

UFI11A is in error status. If you started the UFI11A using the Autosetup DIP switch, 
turn the UFI11A off and on again. If the LED is still on, restart Autosetup by turning 
the DIP switch off and on again. If you started the UFI11A with MOVITOOLS, you 
will see an error message in the status window. Consult the corresponding error 
description.

ON

The UFI11A is not exchanging data with the connected inverters. Either is has not 
been configured or one or more of the connected inverters are not responding. 
Reconfigure the UFI11A. If you started up the UFI11A using Autosetup, please 
switch the Autosetup DIPswitch off and on again. If the LED stays on after Autose-
tup, please check the cabling and the terminating resistors of the SBus as well as 
the inverter voltage supply. If you started up the UFI11A using MOVITOOLS, click 
the "Update" button in the Movitools Manager. All the inverters should be displayed 
in the "Connected Inverters" window. If this is not the case, please check the cabling 
and the terminating resistors of the SBus as well as the inverter voltage supply. 
Reconfigure the UFI11A with MOVITOOLS if necessary. 

Statuts

Meaning

OFF

Standard operating status. The "USER“ LED is reserved for expert mode.

Содержание INTERBUS UFI11A





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды