SEW-Eurodrive EMS Скачать руководство пользователя страница 105

Страница: 105 / 112

103

Transport and storage

Transport and storage

Operating manual [27779165/EN] - EMS modular controls

240

_10

0300

05/EN - 0

2/2

022

Transport and storage

23.1

Safety instructions for transport and storage

INFORMATION

Danger from improper transport and/or storage

Destruction or damage to assemblies
•

Temperature ranges specified in the technical data must be observed.

•

Storage location: inside, dry and without chemical influences.

•

Do not expose to direct sunlight.

•

When delivering and unloading the packages as well as during internal transport, be
careful and observe the symbols on the packaging.

23.2

Transport inspection

Delivery must be checked for completeness and transport damage upon receipt!

In case of visible transport damage, proceed as follows:
•

Do not accept the delivery or only accept it with reservations.

•

Note extent of damage on the transport documents or on the transporter's delivery
slip.

INFORMATION

Risk of damage in transit

Destruction or damage to the assembly, loss of warranty claims
•

Any defect (transport damage) must be reported to the transport company as soon
as it is recognized.

•

Obvious transport damage must be reported to the transport company immediately
or acceptance with reservation. It is at recipient's discretion to refuse delivery accep-
tance in the event of transport damage.

•

All defects must be documented and reported to the manufacturer.

Содержание EMS

















































































































Результаты поиска

Содержание EMS

Отзывы:

SEW-Eurodrive EMS, Руководство по эксплуатации, Страница: 105 / 112

Результаты поиска

Содержание EMS

Отзывы: