Sentiotec just sauna combi Скачать руководство пользователя страница 7

Страница: 7 / 50

WORLD OF WELLNESS

Instructions for installation and use

p. 7/50

2.2. Safety information for the installer

● Installation may only be performed by a qualii ed electrician or

similarly qualii ed person.

●

Work on the sauna control unit may only be performed when the
power has been disconnected.

●

A three-phase shut-off device with a 3 mm contact opening must
be provided during installation. This is provided by the fuse.

●

The sauna control unit must be installed outside the sauna room
at a height of approx. 1.70 m or in accordance with the recom-
mendation issued by the sauna manufacturer. The ambient
temperature must be within a range spanning -10 °C to +40 °C.

●

The heater sensor must be attached in a way that it is not af-

fected by a l ow of air.

●

The heater supply cable must have a minimum cross-section of
2.5 mm

and be temperature resistant up to 150 °C.

●

Also comply with the regulations applicable at the installation
location.

●

For your own safety, consult your supplier in the event of prob-

lems that are not explained in sufi cient detail in the installation

instructions.

Содержание just sauna combi



















































Результаты поиска

Содержание just sauna combi

Отзывы:

Бренды по названию

Популярные бренды

Sentiotec just sauna combi, Инструкция по установке и эксплуатации

Результаты поиска

Содержание just sauna combi

Отзывы:

Бренды по названию

Популярные бренды