background image

SENS EnerGenius Technical Manual  

Service hotline: 1.800.742.2326 
                           1.303.678.7500  

IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLER AND OPERATOR 

1.

SAVE THESE INSTRUCTIONS.

 

2.

DO NOT EXPOSE CHARGER TO RAIN OR SNOW.

 

3. Use of an attachment not recommended or sold by SENS may result in a risk of fire, electric shock, 

or injury to persons. 

4.

ONLY TRAINED AND QUALIFIED PERSONNEL MAY INSTALL AND SERVICE THIS 
UNIT.

 

5.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; shut 
off power at the branch circuit protectors and have the unit serviced or replaced by qualified personnel. 

6.

To reduce risk of electric shock, disconnect the branch circuit feeding the charger before attempting any main-
tenance or cleaning. Turning off controls will not reduce this risk.

 

WARNING: 
RISK OF EXPLOSIVE  
GASES. 

A.

WORKING IN THE VICINITY OF A LEAD-ACID OR NICKEL-CADMIUM BATTERY IS 
DANGEROUS. STORAGE BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL 
BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH 
TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE 
INSTRUCTIONS EXACTLY.

 

B. To reduce the risk battery explosion, follow these instructions and those published by the battery 

manufacturer and the manufacturer of any equipment you intend to use in the vicinity of a battery. Review 
cautionary markings on these products and on the engine. 

  

A. Someone should be within range of your voice or close enough to come to your aid when you work near a  

storage battery. 

B. Have plenty of fresh water and soap nearby in case battery electrolyte contacts skin, clothing, or eyes. 
C. Wear complete eye protection and clothing protection. Avoid touching eyes while working near a storage 

battery. 

D. If battery electrolyte contacts skin or clothing, wash immediately with soap and water. If electrolyte enters 

eye, immediately flood the eye with running cold water for at least 10 minutes and get medical attention 
immediately. 

E.

NEVER

 smoke or allow a spark or flame in vicinity of battery or engine. 

F.

Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short circuit battery 
or other electrical part that may cause explosion. Using insulated tools reduces this risk, but will not 
eliminate it. 

G. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a storage 

battery. A storage battery can produce a short circuit current high enough to weld a ring or the like to metal, 
causing a severe burn. 

H.

Use this charger for charging LEAD-ACID or LIQUID ELECTROLYTE NICKEL-CADMIUM 
batteries only.

 Do not use this battery charger for charging dry cells, alkaline, lithium, nickel-metal-

hydride, or sealed nickel-cadmium batteries that are commonly used with home appliances. These batteries 
may burst and cause injuries to persons and damage to property. 

I.

NEVER

 charge a frozen battery.  

7.

PERSONAL PRECAUTIONS

 

Содержание EnerGenius NRG22-10



















Отзывы: