SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 17

SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 9

350 – 400 – 450 – 500 – 550 – 600

Always make sure the Lock Block are engaged

TERRAIN ADJUSTMENT

In the images below fake rocks have been used to ILLUSTRATE Terrain adjustment. In reality the adjustments will be small. You
should NOT place the ramp on rocky ground. It is better to find a flat even surface to locate the ramp using the PROPER settings.
If you need to adjust the ramp to be MORE stable you can make Terrain Adjustments easily by extending or retracting the legs
INDIVIDUALLY! If the ground is uneven it may take several adjustments to get the ramp stable and SAFE to use. NEVER USE THE
RAMP IF IT IS ROCKING! Standing on the ramp surface is a good way to test stability.

CREATING A 550 CURVED RAMP

2:

Creating a 550 CURVED Ramp is EASY. Turn the ramp on its side so the legs on one side are free to move. You can use the end

ramp surface and turn it to 90 degrees to create a stabiliser. Loosen the Bolt on the (FIRST) SMALLEST Leg so it can be / pushed /
pulled in the slot. Please note that it may be tighter IF the wood is damp and has swollen. Pull the bolt in line with the 5.5 (C)
Marker. Tighten the Bolt.

Loosen the Bolt on the SECOND Leg so it can be / pushed / pulled in the slot. Please note that it may be tighter IF the wood is
damp and has swollen. Pull the bolt in line with the 5.5 (C) Marker. Tighten the Bolt.

«
...
7
8
9
10
11
...
»

Содержание FLY RAMP


















Отзывы:

Нет отзывов