SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 17

SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 7

Replace the two bolts (NO WASHERS) in the back plate and tighten with the 6 mm HEX Key.

Turn your Ramp over and Check ALL BOLTS. ALL LEGS should be located / pushed up against the ramp surface at the end of the
slot for the 350 Setting. IF you look at the markers you will see them ALL AT 350 STRAIGHT MODE. YOU ARE READY TO START
JUMPING



IMPORTANT NOTE! – 350 STRAIGHT MODE CONNECTS WITH OTHER SENDER FEATURES. YOU WILL HAVE

TO USE 60mm BOLTS TO MOUNT FEATURES TO THE BACK OF THE FLY. THESE MUST BE REQUESTED IF

YOU BUY MORE PRODUCTS. PLEASE CALL OR EMAIL FOR HELP.

ADJUSTING YOUR FLY RAMP

UNDERSTANDING THE MARKINGS

Once you adjust the ramp a few times it will become a lot easier and faster! The most important point is to CHECK and TIGHTEN
all bolts BEFORE TAKE OFF or LANDING. Each LEG has an S for STRAIGHT and a C for CURVED. Each FIXED position has a marker
line and height. In the images below you will see as an illustration with a STRAIGHT 350 OR a CURVED 550. The number relates
to the Approximate Height of the LIP of the Ramp from the ground in millimetres.

It is possible to alter the legs to suit your OWN take off (FREERIDE MODE). The Curved settings can be made Steeper or Sweeter.

CREATING A 550 STRAIGHT and then SWITCHING TO A 550 CURVED

1:

Creating a 550 Straight Ramp is EASY. Turn the ramp on its side so the legs on one side are free to move. You can use the end

ramp surface and turn it to 90 degrees to create a stabiliser. Loosen the Bolt on the (FIRST) SMALLEST Leg so it can be / pushed /

«
...
5
6
7
8
9
...
»

Содержание FLY RAMP


















Отзывы:

Нет отзывов