SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 17

SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 6

opposite hole and pull the tooth into the slot / block. This FIT MAY VARY depending on temperature and humidity. IF the ramp
has been outside in the wet the baton will SWELL. You may need a RUBBER MALLET to carefully knock the baton at both ends
until it can be removed. You must DRY all components inside and store dry! The SENDER TEXT must face the BACK / HIGHEST
point of the ramp. IF you remove at an angle you could snap the TOOTH!

7: Take the Back Plate and remove the bolts. Place this face down as shown with the TEETH Towards you. Unfold / Open the
Wings and locate the BLOCK ENDS into the SLOTS on the sides. Press / Push the middle of the back plate so the Ends go into and
through the slot in the sides. It is important not to over force these or you could damage the ramp. If the ramp is wet the fit will
be tight! Take Care.

Check the sides are flush with the Back Plate. Your FLY was PRE ASSEMBLED and CHECK for full function in the Factory!
Everything fits and works perfectly BEFORE Packing.

«
...
4
5
6
7
8
...
»

Содержание FLY RAMP


















Отзывы:

Нет отзывов