SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 17

SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 3

RAMP SURFACES AND SIDES – BACK PLATE

CURVED RAMP SETTING STABILISERS – CROSS BATONS

1:

Remove the packing carefully without using a knife in case you cut the bag. You will find additional packaging not shown in the

images. Pull the Back Plate from the bag first. Lie the bag on one side or hold the Blue Strap and pull the ramp from its bag
vertically. Beware as there are additional loose parts inside the folded ramp.

2:

The FLY EXTENSION is bolted to the inside when the ramp is folded. Undo these bolts with a 6 mm Hex Key (On your bike

tool).

3: Unfold the ramp until the Ramp Surface is exposed. Please take care when turning the ramp over not scratch or mark the take
off! The Ramp is now lying face down so you can see the sides.

It is always best to set the ramp up for use in the EASIEST 350

Straight MODE FIRST!

At least until you are familiar with the set up process. First we will join the two lower SIDE PANELS using

the BIG LOCK BLOCK with the SKULL.

«
1
2
3
4
5
...
»

Содержание FLY RAMP


















Отзывы:

Нет отзывов