SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 17

SENDER RAMPS FLY RAMP Скачать руководство пользователя страница 11

CHECK that BOTH small and large LOCK BLOCKS are LOOSE! Turn the ramp over so the legs on the other side are free to move.
Use the Ramp Surface as a stabiliser and be very careful when rotating not to damage the surfaces. It is better to LIFT the ramp
and sit it on a protective surface. REPEAT ALL the processes above until all Legs are set to 550 CURVED.

LIFT / TURN the Ramp over onto its feet. The LOCK BLOCKS should be loose.

MANIPULATE

the ramp surface so ALL the adjusted

legs are touching the ground. Make sure that the Bolts in the Lock Blocks are in the slot or this will not be possible! DO NOT
TERRAIN ADJUST AT THIS STAGE. Once you are happy all legs are touching down tighten all 8 Bolts on the Lock Blocks to

FIX THE

CURVED POSITION

. Go around and CHECK ALL BOLTS are TIGHT.

FITTING THE CURVED STABILISER LEGS – NO STABILISERS NO JUMP!

The FLY is NOT SAFE TO USE IN CURVED MODE WITHOUT THE STABILISERS FITTED

. IT WILL TIP. Fitting is EASY once you are

familiar with the system. Take the two CURVED STABILISER LEGS. At the top of the leg is a fixed bolt protruding through the T
NUT. This end of this Bolt goes into the hole that matches the height setting you have already set the legs. 5.5 = 5.5 (Cross) Hole

«
...
9
10
11
12
13
...
»

Содержание FLY RAMP


















Отзывы:

Нет отзывов