SELWOOD MEADOWSIDE II F24021E Скачать руководство пользователя страница 41

Страница: 41 / 44

www.selwoodproducts.com

Step 23: Optional SW Mount Installation

If you have purchased a 2- or 3-Position Monkey Ladder Swing to add to your fort complete this step.

If you have purchased 3-Position Swing II, refer to that manual.

On the Back of the Swing Side remove the 2 (H2) 1/4 x 2” Hex Bolts (with lock washer and flat washer) which

attach the (2445) Side Top and (2448) SW Floor to the (2469) Post. The t-nuts can be left in. (fig 23.1 and 23.2)

Place (2446) SW Mount over the bolt holes, noticing the holes on the sides are towards the top of the board,

and attach with 2 (H7) 1/4 x 5-1/2” Hex Bolts (with previously removed lock washer and flat washer). (fig. 23.1

and 23.3)

Fig. 23.1

2448

Notice hole locations.

2469

2446

Wood Parts

Hardware

1 x

SW Mount 2 x 4 x 34”

2 x

1/4 x 5-1/2” Hex Bolt (previously removed 1/4” lock washer, 1/4” flat washer)

2446

1/4” Flat

Washer

1/4” Lock

Washer

Back

Remove these 2 bolts.

Fig. 23.3

Fig. 23.2

2445

Swing Side

2445

2448

Содержание MEADOWSIDE II F24021E













































Результаты поиска

Содержание MEADOWSIDE II F24021E

Отзывы:

Похожие инструкции для MEADOWSIDE II F24021E

Бренды по названию

Популярные бренды

SELWOOD MEADOWSIDE II F24021E, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MEADOWSIDE II F24021E

Отзывы:

Похожие инструкции для MEADOWSIDE II F24021E

Бренды по названию

Популярные бренды