SELWOOD MEADOWSIDE II F24021E Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

background image

26

www.selwoodproducts.com

1779

A:

Attach (1779) CE Access Board flush to the top and outside edges of each (2470) Rock Rail with 4 (S2) #8 x

1-1/2” Wood Screws. (fig. 11.1 and 11.2)

B:

Below (1779) CE Access Board stagger 3 (1777) CE Rock Board B and 2 (1778) CE Rock Board A, making

sure they are evenly spaced with a minimum 2-1/4” and maximum 2-3/4” gap. The sides are flush to the outside

edges of each (2470) Rock Rail. Attach using 4 (S2) #8 x 1-1/2” Wood Screws per board. (fig. 11.1 and 11.2)

Place the CE Rock Boards as you desire, but watch the hole placement to prevent rocks from forming a

straight line.

Note: Gaps

between boards

2-1/4”, not to

exceed 2-3/4”

Note: The holes

in the rock boards

must orient to the

top of the boards.

Step 11: Rock Wall Assembly

Wood Parts

1 x

CE Access Board 1 x 6 x 17”

3 x

CE Rock Board B 1 x 6 x 17”

2 x

CE Rock Board A 1 x 6 x 17”

24 x

#8 x 1-1/2” Wood Screw

1779

S2

Hardware

1777

1778

Fig. 11.1

1778

2470

1777

x 4 per board

1777

Fig. 11.2

1778

1777

S2

Flush

Flush

«
...
24
25
26
27
28
...
»

Содержание MEADOWSIDE II F24021E













































Отзывы:

Нет отзывов

Похожие инструкции для MEADOWSIDE II F24021E

Бренд: Bacharach Страницы: 31

Бренд: Backyard Play Systems Страницы: 52

Бренд: Backyard Play Systems Страницы: 19

Бренд: Backyard Play Systems Страницы: 44

Бренд: Bacharach Страницы: 2

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Gamry Instruments Страницы: 69

Бренд: Rayger Страницы: 2

Бренд: MacDon Страницы: 2

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Бренд: Ebyte Страницы: 7

Бренд: Ganter Norm Страницы: 20

Бренд: IDS Страницы: 68

Бренд: Waeco Страницы: 254

Бренд: HAGS Страницы: 9

5x13 Chicken Coop Plan

Бренд: EASY COOPS Страницы: 22

Бренд: Digga Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды