SELWOOD MEADOWSIDE II F24021E Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

SELWOOD MEADOWSIDE II F24021E Скачать руководство пользователя страница 30

30

www.selwoodproducts.com

Step 14: Attach Roof Supports to Fort

A:

From inside the assembly, on the Cafe Side, attach (2451) Tarp Support to (2445) Side Top and (2448) SW

Floor with 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut). The support should be tight to the

floor boards. (fig 14.1)

B:

From outside the assembly, on the Swing Side, attach (2447) SW Mount to (2445) Side Top and (2448) SW

Floor with 2 (G4) 5/16 x 4” Hex Bolt (with lock washer, flat washer and t-nut). Bolts are to be installed from inside

the assembly. (fig. 14.1)

Fig. 14.1

2451

5/16” Lock

Washer

2447

2445

Wood Parts

Hardware

1 x

SW Mount 2 x 4 x 53-3/4”

1 x

Tarp Support 2 x 2 x 53-1/8”

2 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

5/16 x 4” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

2447

2451

G4

H2

5/16” Flat

Washer

5/16”

T-Nut

Swing Side

Cafe Side

H2

G4

1/4” Flat

Washer

1/4”

T-Nut

1/4” Lock

Washer

2445

2448

2448

«
...
28
29
30
31
32
...
»

Содержание MEADOWSIDE II F24021E













































Отзывы:

Нет отзывов