SELWOOD MEADOWSIDE II F24021E Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 44

SELWOOD MEADOWSIDE II F24021E Скачать руководство пользователя страница 34

34

www.selwoodproducts.com

Step 18: Attach Canopy to Roof Frame

A:

Place Canopy over (1900) Ridge making sure bottom edges of tarp are even on both sides of assembly.

(fig. 18.1)

B:

Secure one side by attaching Canopy to 1 (1796) Top End using 6 evenly spaced (S5) #8 x 1/2” Pan Screws

(with #8 flat washer). Make sure the screws are 1/2” in from the edge of the canopy. (fig. 18.1)

C:

Make sure the canopy is smooth and tight then secure opposite end of canopy to the other (1796) Top End

using 6 evenly spaced (S5) #8 x 1/2” Pan Screws (with #8 flat washer). Make sure the screws are 1/2” in from

the edge of the canopy. (fig. 18.1)

D:

Attach canopy to (1900) Ridge with 1 (S5) #8 x 1/2” Pan Screws (with #8 flat washer) at each end. (fig. 18.1)

Other Parts

Hardware

Fig. 18.1

14 x

#8 x 1/2” Pan Screw (with #8 flat washer)

S5

1 x Canopy

S5

1796

x 6 per side with #8

flat washer

1900

1796

Canopy

S5

«
...
32
33
34
35
36
...
»

Содержание MEADOWSIDE II F24021E













































Отзывы:

Нет отзывов