SELWOOD MEADOWSIDE II F24021E Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 44

background image

18

www.selwoodproducts.com

Step 5: Attach Chalk Wall Tarp to Fort

Part 1

A:

On the back of the assembly, from the inside, tuck Chalk Wall Tarp between (2463) Floor Back and both

(2469) Posts. Align Chalk Wall Tarp to edge of both (2469) Posts and place just below second hole from the top

of the posts. (fig. 5.1)

B:

Measure 4” down from the top of each (2469) Post then make sure Chalk Wall Tarp is smooth and tight and

attach to the outside of each (2469) Post, 1/2” in from the edge of the tarp, with 4 evenly spaced (S5) #8 x 1/2”

Pan Screws (with #8 flat washer) per post. (fig. 5.1 and 5.2)

C:

Make sure assembly is square then tighten bolts in (2463) Floor Back and (1764) Floor Front.

D:

Attach (2463) Floor Back to both (2469) Posts and (1761) Side Joist with 4 (S7) #12 x 2” Pan Screws (with

3/16” flat washer) as shown in fig. 5.1 and 5.2.

Other Parts

1 x Chalk Wall Tarp

8 x

#8 x 1/2” Pan Screw (#8 flat washer)

4 x

#12 x 2” Pan Screw (3/16” flat washer)

Hardware

Fig. 5.1

S5

Fig. 5.2

2469

2469

2469

2463

with

#8 Flat

Washers

Chalk Wall Tarp

Back

with

#8 Flat

Washers

S7

with

3/16” Flat

Washers

S7

S5

S5

Chalk Wall Tarp

with 3/16”

Flat Washer

S7

2463

4”

1764

1761

(hidden)

Just below

this hole

«
...
16
17
18
19
20
...
»

Содержание MEADOWSIDE II F24021E













































Отзывы:

Нет отзывов

Похожие инструкции для MEADOWSIDE II F24021E

Бренд: ABB Страницы: 86

Бренд: TAIKO Audio Страницы: 24

Бренд: MacDon Страницы: 2

Бренд: JDS Uniphase Страницы: 144

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 14

Бренд: ?HC Страницы: 2

Бренд: Land Pride Страницы: 72

Бренд: KAPPLER Страницы: 28

Бренд: Stagg Страницы: 13

Бренд: Petzl Страницы: 2

Бренд: Quadro Страницы: 2

Бренд: Propellerhead Страницы: 14

Бренд: Kellfri Страницы: 32

Бренд: Retsch Страницы: 25

Бренд: Aseptico Страницы: 16

Diamond_GS-DB101

Бренд: GSWeb Playground Equipment Страницы: 13

Бренд: PR Lighting Страницы: 30

Climb N Explore

Бренд: grow 'n up Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды