SELWOOD MEADOWSIDE II F24021E Скачать руководство пользователя страница 15

Страница: 15 / 44

www.selwoodproducts.com

Step 3: Swing Side Wall Assembly

Loosely attach (1792) Lower Side and (2448) SW Floor with 4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat

washer and t-nut) per board; and (2445) Side Top using 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer

and t-nut) to 2 (2469) Posts as shown in fig. 3.1. Notice the hole locations in (2448) SW Floor and (2445) Side

Top must be 9” from the (2469) Post shown in fig. 3.1.

Note: Pre-drill all holes using a 1/8” drill bit before installing the Lag Screws.

Make sure assembly is square and then loosely attach (0369) Lower Diagonal to (1792) Lower Side on the

one side shown in fig. 3.1, with 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, flat washer and t-nut), notice this is the

opposite side from Step 2. Fasten (0369) Lower Diagonal to (2469) Post using 1 (LS3) 1/4 x 3” Lag Screws (with

flat washer). (fig. 3.1)

Tighten all bolts.

Fasten (2445) Side Top to both (2469) Posts using 2 (S2) #8 x 1-1/2” Wood Screws. (fig. 3.1)

Wood Parts

Hardware

Fig. 3.1

1/4” Flat

Washer

1/4”

T-Nut

1/4” Lock

Washer

2 x

Post 2 x 4 x 82”

1 x

Side Top 1 x 4 x 51-1/2”

1 x

SW Floor 1 x 6 x 26-7/8”

1 x

Lower Side 1 x 5 x 62-3/8”

1 x

Lower Diagonal 2 x 3 x 37”

2469

11 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

1/4 x 3” Lag Screw (1/4” flat washer)

2 x

#8 x 1-1/2” Wood Screw

1792

2448

2445

Notice the hole

locations

2445

1792

0369

LS3

1/4” Flat

Washer

9”

0369

2469

9”

2448

Содержание MEADOWSIDE II F24021E













































Результаты поиска

Содержание MEADOWSIDE II F24021E

Отзывы:

Похожие инструкции для MEADOWSIDE II F24021E

Бренды по названию

Популярные бренды

SELWOOD MEADOWSIDE II F24021E, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MEADOWSIDE II F24021E

Отзывы:

Похожие инструкции для MEADOWSIDE II F24021E

Бренды по названию

Популярные бренды