1. Precautions on Usage
Handle the device with the following in mind so as to enable the functions of it to be fully utilized.
(1) Before usage, make sure that the power cord is firmly connected to an outlet. Avoid connecting or
disconnecting the connector during operation or while the power switch is turned on.
(It may result in a failure.)
(2) Since the card reading part is equipped with an optical lens, never insert a screwdriver or the like.
(Otherwise, reading may be disabled.)
If card feeding is disabled due to clogged dust or the like in the card feeder, open the top cover to
remove it. (Refer to "11. Cleaning".)
(3) Allow an interval of at least 5 seconds between turning the power switch on and off.
(Otherwise, a failure may result.)
(4) Be sure to ground the device so as to prevent noise or static electricity from damaging the device.
Also, do not touch the metallic part of the device during card feeding operation.
If the device is used without being grounded or the metallic part is touched, malfunction or an elec-
tric shock may result.
(5) Do not place the device in a place subject to direct sunlight or near a heater. Also be careful not to
allow sudden temperature change, moisture, dust or excessive shock around the device.
(Otherwise, a failure like wrong paper feeding, reading or operation may occur.)
(6) When the device is not in use for long periods, insert the paper feeding roller protection card between
the paper feeding roller and the separation pad to prevent the roller material from deteriorating.
(7) If the paper feeding roller becomes soiled with powder from card paper or pencil, the roller and the
card may slip.
In order to prevent it, clean the paper feeding roller at proper intervals. (Refer to "11. Cleaning".)
(8) If the exterior of the device is soiled, slightly wipes with soft cloth wetted with water or neutral
detergent. Note that wiping with cloth wetted with volatile chemicals like benzine or thinner may
cause deforming or decoloring.
1.Precautions on Usage
(9) When connecting by RS-232C, consult with the distributor.
(10) Use only the USB cable and power cord that came with the device.
2. Names of Each Part
2.Names of Each Part
TEST LED (yellow)
Power switch
READY LED (green)
POWER LED (orange)
Total counter
RS-232C connector
Fuse holder
Power connector
Power cord
Ground terminal (reserved)
ERROR LED (red)
Clear switch
Feed switch
USB connector
- 1 -
Содержание SR-450
