5-B Functions and Operating Method of Operation Panel
The operation panel is equipped with the following two switches and four LEDs (lamps):
(1) Functions of switches
FEED
: Pressing this switch feeds one card.
CLEAR
: Clears an error, if any.
The hardware or cover open error, however, cannot be cleared.
(2) Meanings of LED display
TEST (yellow)
: Comes on in the test mode.
ERROR (red)
: Comes on when an error occurs.
READY (green)
: Comes on when communication is enabled.
POWER (orange)
: Comes on when the power is turned on.
Operation panel
TEST
ERROR
READ
Y
POWER
CLEAR
FEED
5.Operation
5-C Setting Cards
(1) Pressing the [PUSH] button on the left of the hopper generates a "clicking" sound to lock the
hopper at the card setting position. Pressing the [PUSH] button again unlocks the hopper to
raise it. Do not unlock it by pressing the card.
(2) Set cards while the hopper is lowered at the setting position. Set them with the marked surfaces
facing upward and the timing mark sides facing left.
At this time, well-align the cards. Pay particular attention to the ends of the cards since a paper
feeding error may occur unless they are well-aligned.
(3) Press the side guide hard to the cards so that no clearance is allowed between them. Otherwise,
a reading error may occur.
When moving the side guide, keep pressing the guide lock lever (green). The side guide is fixed
when the lever is released.
(4) For the maximum card number settable onto the hopper, refer to the side guide index.
Note that setting too many cards on it may result in a paper feeding error or misreading.
(5) When using long-sized cards, raise the guide wire toward the external side of the hopper.
Pressing once: Locks the hopper.
twice: Unlocks the hopper.
Guide wire
How to move side guide
Slide it right and left while keep
pressing the guide lock lever (green).
Side guide index
5.Operation
- 13 -
Содержание SR-450
