13. Appendix
13-A Card creation reference
(1) Overall dimensions of card
For details of dimensions of cards, refer to the reference drawing in 13-A-(6).
Note: When using carbon paper, design it so as not to allow the pasting position to overlap
the end of the card feeding direction.
(2) Print ink
Be sure to use print ink satisfying the following reflectance characteristics:
9
.
0
=
S
C
P
f
o
)
k
c
al
b
(
k
n
i
e
c
n
at
c
el
f
e
r-
n
o
N
:
k
r
a
m
g
n
i
m
i
T
)
1
±
0.05
2) Unreadable information in marked area: Drop-out color (*1) of PCS = 0.15 or lower
3) Direction of fiber
: Parallels the longer side of paper (direction of card
feeding).
4) PCS measurement wavelength
: 940nm for the near infrared ray
(660nm for the visible red ray)
Note 1: Drop-out color
Refers to a color which is not read by optical mark read elements due to being converted to the
same signals as "blank" parts although visible as various colors to human eyes.
Direction of fiber
Timing mark
Length (longer side)
htdi
W
13.Appendix
h
t
d
i
h
W
t
g
n
e
L
d
r
a
c
d
e
zi
s-
d
r
a
d
n
at
S
d
r
a
c
d
e
zi
s-
d
r
a
ct
s
o
P
d
r
a
c
d
e
zi
s-
g
n
o
L
e
zi
s
r
e
h
t
o
f
o
d
r
a
C
148〜304.8mm
±
~
±
±
±
(3) Printing of timing mark
* For postcard-sized cards, use the timing mark control type.
(4) Mark entry frame (fixed value for standard-sized card)
a. Dimensions (rectangle)
: Height (V) = 0.8 to 1.5mm
Should be less, however, than the timing mark width (W).
: Length (H): 3.5 to 4.3mm
b. Print color
: Use a drop-out color and set the PCS value to 0.15 or lower.
(5) Corner-cut
When cutting one corner of cards for reference to align cards, cut the opposite side from the
timing mark side by 5mm or less.
A
0.1 A
0.1
Timing mark
Mark frame
Left end of card
V
H
L
P
W
D
13.Appendix
13-A-(6)
Min. 2.5mm
2.21mm
1.21mm
Min. 1.5mm
Min. 4.17mm
Min. 2.5mm
1.5 ~ 30.0mm
- 56 -
Содержание SR-450
