Seg XRN2, Руководство пользователя

Страница: 7 / 40

TB XRN2 02.00 E 7
3.2.2 Display
Function Display shows Pressed pushbutton Corresponding
LED
Type of relay
Normal operation

SEG
all types
Measured operating values
Actual measured value
Min. and max. values of
voltage, frequency and
vector surge <SELECT/RESET> one time
for each value L1, L2, L3,
f, min, max
∆Θ
df
XRN2-1
XRN2-2
Setting values:
star/delta connection
Y/DELT <SELECT/RESET><+><->
∆
/Y
undervoltage (low set)
tripping delay of low set element setting value in volt
setting value in seconds <SELECT/RESET><+><->
one time for each value U<
t
U<
undervoltage (high set)
tripping delay of high set element setting value in volt
setting value in seconds <SELECT/RESET><+><->
one time for each value U<<
t
U<<
overvoltage (low set)
tripping delay of low set element setting value in volt
setting value in seconds <SELECT/RESET><+><->
one time for each value U>
t
U>
overvoltage (high set)
tripping delay of high set element setting value in volt
setting value in seconds <SELECT/RESET><+><->
one time for each value U>>
t
U>>
rated frequency setting value in Hz <SELECT/RESET><+><-> f
N
frequency measuring repitition setting value <SELECT/RESET><+><-> T
frequency element f
1
tripping delay of frequency element f
1
setting value in Hz
setting value in seconds <SELECT/RESET><+><->
one time for each value f
1
t
f1
frequency element f
2
tripping delay of frequency element f
2
setting value in Hz
setting value in seconds <SELECT/RESET><+><->
one time for each value f
2
t
f2
frequency element f
3
tripping delay of frequency element f
3
setting value in Hz
setting value in seconds <SELECT/RESET><+><->
one time for each value f
3
t
f3
1-of-3/3-of-3 measurement 1Ph/3Ph <SELECT/RESET><+><-> 1/3 XRN2-1
threshold for vector surge setting value in degree <SELECT/RESET><+><->
∆Θ
XRN2-1
setting value df/dt
measuring repitition df/dt setting value in Hz/s
setting value in periods <SELECT/RESET><+><->
one time for each value
df
dt
XRN2-2
Blocking EXIT <+> until max. setting value LED of blocked
parameter
Undervoltage blocking of
frequency and vector surge meas-
uring (df/dt for
XRN2-2 )
setting value in Volt <SELECT/RESET><+><->
f,
∆Θ
, df
Slave address of serial interface 1 - 32 <SELECT/RESET><+><-> RS
Recorded fault data:
star--connection:
U1, U2, U3
tripping values in Volt <SELECT/RESET><+><->
one time for each phase L1, L2, L3,
U<, U<<,
U>, U>>
delta-connection:
U12, U23, U31 tripping values in Volt <SELECT/RESET><+><->
one time for each phase L1, L2, L3
U<, U<<,
U>, U>>
frequency tripping values in Hz <SELECT/RESET><+><->
one time for each phase f, f1, f2, f3
rate of change of frequency tripping value in Hz/s <SELECT/RESET><+><-> df XRN2-2
vector surge tripping value in degree <SELECT/RESET><+><->
one time for each phase
∆Θ
+ L1, L2 or L3 XRN2-1
Save parameter? SAV? <ENTER>
Save parameter! SAV! <ENTER> for about 3 s
Software version First part (e.g. D02-)
Sec. part (e.g. 6.01) <TRIP>
one time for each part
Manual trip TRI? <TRIP>
three times
Inquire password PSW? <SELECT/RESET>/
<+>/<->/<ENTER>
Relay tripped TRIP <TRIP> or fault tripping
Secret password input XXXX <SELECT/RESET>/
<+>/<->/<ENTER>
System reset

SEG <SELECT/RESET>
for about 3 s
Table 3.1: possible indication messages on the display