Securam SafeLogic Xtreme Скачать руководство пользователя

Страница: 2 / 17

SafeLogic Xtreme Installation and Operation Instructions

Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc.

Page 2

EC-1501A-X EntryPad.

XL-1501 Electromechanical Lock Body.

Spindle – drilled and tapped at one end.

Combination Change Key.

Lock Mounting Bolt: 3 PCS. Used to install the electromechanical lock body to the mounting

plate.

Spindle Bolt to secure the spindle to the SpinDial: 1 PC.

DialRing Mounting Bolt: 4 PCS. Used to install the EntryPad to the front of the safe door. 8.

Clear Plastic Spindle Tube

IMPORTANT: Do NOT use power tools to install the SafeLogic Xtreme.

1.0 Preparing to Install the DialRing and EntryPad

Separate the DialRing from the EntryPad:

Step 1: Pull up on the SpinDial release to disengage the electronics.

Step 2: Rotate the EntryPad 180 degrees to gain access to the EntryPad bolt which is located at

Содержание SafeLogic Xtreme


















Результаты поиска

Содержание SafeLogic Xtreme

Отзывы:

Похожие инструкции для SafeLogic Xtreme

Бренды по названию

Популярные бренды

Securam SafeLogic Xtreme, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SafeLogic Xtreme

Отзывы:

Похожие инструкции для SafeLogic Xtreme

Бренды по названию

Популярные бренды