Seagull Models Husky Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 32

background image

3

www.seagullmodels.com

ADDITIONAL ITEMS REQUIRED.

0.61- 0.75 2-stroke.

0.91 4-stroke.

Computer radio with 7 servos.
Glow plug to suit engine.
Propeller to suit engine.
Protective foam rubber for radio
system.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.

SEA180 CHRISTEN HUSKY 2030mm

SEA18001 Fuselage
SEA18002 Wing set
SEA18003 Tail set
SEA18004 Cowling :
SEA18005 Main Landing Gear
SEA18006 Tail Gear
SEA18007 Windshield Set
SEA18008 Decal Set
SEA18009 Linkage Set
SEA18010 Wing Tube
SEA18011 Fiberglass Wheel pants
ZZBSEA180B Replacement Box
FL180 Floating set for Christen Husky

KIT CONTENTS.

TS

HINGING THE FLAP

M2x10mm.

M2x10mm.

«
1
2
3
4
5
...
»

Содержание Husky

































Отзывы:

Нет отзывов

Похожие инструкции для Husky

Бренд: Hobbico Страницы: 28

LionChief Plus NW2 Diesel 546

Бренд: Lionel Electric Trains Страницы: 5

Atlantique 040250

Бренд: Jamara Страницы: 8

He 111H-6 nose interior

Бренд: Eduard Страницы: 6

KICK`N CRAWL BARN 71699

Бренд: Fisher-Price Страницы: 4

Бренд: BT21 Страницы: 2

Бренд: REVELL Страницы: 7

Бренд: Trix Страницы: 24

Бренд: Eduard Страницы: 4

Бренд: AMATI Страницы: 56

Бренд: Stevens AeroModel Страницы: 27

Branchline Class 03

Бренд: Bachmann Страницы: 3

Бренд: Volvo Страницы: 10

Бренд: Knights of Dice Страницы: 7

Бренд: Viessmann Страницы: 4

Бренд: Trix Страницы: 40

Бренд: Propel RC Страницы: 4

Бренд: GRAUPNER Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды