Seagull Models Husky Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 32

background image

CHRISTEN HUSKY

Instruction Manual.

24

INSTALLATION PILOT AND CANOPY.

1) Locate items necessary to install pilot, seats
.

2) A scale pilot is included with this ARF. The
Seagull Pilot included fitting well to the cockpit.
(or you can order others scale pilot figures
made by Seagull factory. They are available at
Seagull distributors.)

If you are going to install a pilot figure, please
use a sanding bar to sand the base of the figure
so that it is flat.

3 x 20mm.

Epoxy

3x25 mm.

Aluminum tail
landing gear.

«
...
22
23
24
25
26
...
»

Содержание Husky

































Отзывы:

Нет отзывов

Похожие инструкции для Husky

DYSTOPIAN WARS MEXICO

Бренд: WARCRADLE STUDIOS Страницы: 6

Бренд: Faller Страницы: 8

Бренд: Trix Страницы: 12

Бренд: Velleman Страницы: 8

U.S. GENERAL Junior 56515

Бренд: Harbor Freight Tools Страницы: 8

Hellcat Little Nugget

Бренд: H-KING Страницы: 18

SH-3 Sea King interior

Бренд: Eduard Страницы: 2

MEGA BLOKS SKYLANDERS 95305

Бренд: Activision Страницы: 2

Origami 3D Fox 2575

Бренд: Alexander Страницы: 68

Бренд: Techno Gears Страницы: 2

MaK Typ DE 1002 HGK

Бренд: marklin Страницы: 32

Бренд: marklin Страницы: 28

EINSCHLAFHILFE EULE

Бренд: X4-TECH Страницы: 36

Бренд: LEXIBOOK Страницы: 1

Crane Car American Flyer

Бренд: Lionel Страницы: 8

Бренд: Faller Страницы: 16

BOEING F-15E STRIKE EAGLE W/BUNKER BUSTER

Бренд: Tamiya Страницы: 29

Бренд: Curtiss Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды