background image

Rev. 2013.08.19 

16 

 

 
Note:   

Decimal values “roll-over” from 999999.99 to 0.00 

 

 

Integer counts “roll-over” from 49999 to 0 

 

NOTE:   FOR SECURITY PURPOSES, TOTALS DO NOT ZERO OUT AFTER EACH TIME YOU 
DISPLAY TOTALS. 

 

PRICE SETTING 

 

Price Setting is performed by selecting Service Code PS.  
 

1.  Press the Scroll buttons (

9

 and 

10

) repeatedly until the LCD          Displays    PS.-- 

 
 

You are now in Price Setting Mode 

 
2.  Make a selection (Alpha then number) to display the current price 

 

Displays the row and column and then  **. ** 

 

3.  Using the numeric keys, set the price for this selection (the 

10

 button is interpreted as a 

zero) by entering 4 digits. The display will then revert to PS when this is complete. 

 

Prices may be set from 00.00 to 

99.95

.  

 
4.  Press two Alpha selections (Ex: “A” then “A”) then a number (price) to set the price for 

an entire tray at once. Pressing three Alpha selections (AAA) allows all the prices to be 
set in one operation. 

 

TEST MODE 

 

1. Press the scroll buttons (

9

 and 

10

) repeatedly until

 

Displays tE.- 

In Test Mode, making a selection (Alpha then numeric) will operate the selected motor.  
 
Press selection button 1 for a single test vend on ALL selections. 
Press selection button 2 to test the positive vend sensor (if enabled). 
Press selection button 3 to test Relay output 1 (Compressor Cycle). 
Press selection button 4 to test Relay output 2 (Defrost). 
 
Note :  You must be in Test mode to manually empty the coin changer.  
 

WARNING : THIS MENU OPTION DOES NOT TIME OUT AFTER 30 SECONDS 

 

CONTROL WORD 

 

1. Press the Scroll buttons (

9

 and 

10

) repeatedly until the LCD 

(where ** is current value) 

You are now in Control Word Setting

 

Displays Ct. 

** 

2. Press Selection Button 

1

 to 

4

 to change the control word

Displays Ct.** 

 

 

 

The control word is now set 

 

 

 

 

***RECOMMENDED CODE:     

2

 

 
 
 
 
 

Содержание OD14F


































Отзывы: