SEA ISUZU FSR Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 56

background image

OWNER

’

S MANUAL

(

SEA ISUZU FSR/FSD EV)

SEA-OWS-QA-004/5

ISSUE DATE:

30/05/2020

Page

41

of

56

12- Towing Procedure

The vehicle can be recovered by:

•

Rear wheels raised and front wheels on the ground.

(Preferred method)

Caution

Release the parking brake and shift the gearshift lever to neutral gear.

•

Front wheels raised and rear wheels on the ground.

Caution

Ask tow operators to do one of the below methods for your vehicle.
Alternative1: Disconnect Prop Shaft from diff or completely remove.
Alternative2: Remove the drive shaft from the diff (Preferred method)
Release the parking brake and shift the gearshift lever to neutral gear.

The maximum towing speed is 65km/h when the rear wheels are on the ground.

Warning:

Do not tow vehicle with driven wheels

WARNING:

•

The vehicle will not have power steering when not powered up

•

The vehicle will not have air brakes when not powered up

«
...
39
40
41
42
43
...
»

Содержание ISUZU FSR

























































Отзывы:

Нет отзывов

Похожие инструкции для ISUZU FSR

Бренд: RAM Commercial Страницы: 172

Power-Reach PR12

Бренд: Boughton Страницы: 42

Бренд: Mitsubishi Fuso Страницы: 467

Бренд: Still Страницы: 110

Бренд: Hino Motors Страницы: 169

Бренд: U-Line Страницы: 4

Бренд: Magliner Страницы: 64

International eMV Series

Бренд: Navistar Страницы: 22

Бренд: Powerfix Profi Страницы: 16

Бренд: Powerfix Profi Страницы: 15

Бренд: Powerfix Profi Страницы: 17

Zero Radius ZR 12 ft. Extended Reach

Бренд: McNeilus Страницы: 118

HARRINGTON HPC500 Series

Бренд: KITO Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды